Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi. I tested extended advertising of Bluetooth 5 with examples, ble_app_rscs_c and ble_app_rscs , in SDK 15.2. It works well.
And I added 216 bytes manufacturer's data to...
Hi,
I am doing a job with nRF52832 with keil in initial period. I have two peripherals and connect to nRF52832 via uart, and it runs well. Recently, I migrate the job to...
Hello ,
I have met a problem about the communication between nrf52832 and nrf24le over Gazell. nrf52832 is the device and nrf24le is the host. The problem is that nrf24le...
https://devzone.nordicsemi.com/b/blog/posts/measuring-lithium-battery-voltage-with-nrf52
Following the calculations as so, I have worked out the necessary capacitor values...
Hi,
I am using the command line tool nrfjprog to read the device MAC address using the following command:
nrfjprog --memrd 0x100000A4 --w 8 --n 6
I am connected using...
hello,
I want to use nRFgo studio download hex for NRF52810, but I have a problem as follows:
I do not know how to solve the problem, thank you very much!
best regards...
Hi,
I'm using an application based on the light switch provisioner example (BLE mesh 2.2.0).
I'm wondering if the following is possible:
- Request all provisioned nodes...
Sir/Madam,
I am developing application software using nRF51822 in keil microvision 5 IDE. I want to know how to download the hex file without using KEIL IDE. I found the...
I'm looking for an equivalent simple DFU bootloader over UART similar to the HCI example which was provided in the nRF5 v11.0.0 SDK.
Currently, I'm developing with the Sparkfun...
hi,i have a problem! How to Optimize code space in nRF52810,s112,SDK15.2.0,example ble_app_hids_keyboard.
my method is that disable all the code which run in main function...
Hi all,
Now, I have a troube. In Mesh 3.0, I want to advertising data. This is my function :
#define ADVERTISER_BUFFER_SIZE (128)
And whenever the data changes, I...
I bought a nRF52840 Dongle, to evaluate the use of nRF52840 for ZigBee purposes.
I have been able to flash such firmwares as \examples\peripheral\blinky\hex\blinky_pca10056_mbr...
I have a custom board where both nRF52840 and nRF52832 SOC in it.
i have flashed example Ble_Uart code from sdk15 in nRF52840 but im facing a serious issue.
i can able...
