Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I'm attempting to get our wearable remote to interact with a GoPro using their API and am getting the error in the subject line when attempting to start scanning. I've checked...
I am working on scanning and connecting to an iPhone device in NRF52840dk, but I am not able to receive my iPhone while scanning. If there are any different ways, please let...
Hello!
Looking for some guidance on how I should start debugging an issue I'm experiencing trying to get the Zephyr fdc2x1x sample code running on a custom PCB that uses...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
I am trying to install the nrf connect SDK on my Macbook M3 Pro. But i am unable to do so. Neither VSCode extension nor the Toolchain manager works for me.
Clicking install...
I'm currently troubleshooting potential timing-related collisions associated with the NRF radio. I use a custom protocol on a single specified channel (no frequency hopping...
Hi, I have a custom board built around a nRF9161. When I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the expected string. All other commands...
Hi all
I'm working on custom board build with an nrf9161. Right now I'd like to use a gpio as input with interrupt for i2c captor icm20948. So for I've searched and I think...
Hello.
I have 2 designs of PCB to make, I have their schematics almost complete. Both use the nRF52840.
My doubt is if for each PCB, if I will be able to use at the same...
Hi
Can you please supply me with the mechanical dimensions for the nrf52840 dk? I can not find anything. I would like to have the dimensions of the mounting holes in relation...
Hi,
Previously, I used the nRF52840 to work as a host. Similarly now, I hope to use the nRF52832 to work as a host, but it seems that this cannot be achieved simply by changing...
I am facing error while building the sample "Hello World for multiple board targets using Sysbuild" without changing anything in the sample. I am using nRF connect SDK and...
I have a custom board with a nrf52832 chip on it and I am currently trying to build my own application for it.
I have successfully managed to compile and flash it using...
I am using NCS 2.7.0
i am running this build command from a terminal in VSC for the nrf/samples/bluetooth/Direction_finding_connectionless_tx sample
west build -p -b nrf5340dk...
