Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I can't seem to get printf working on the ble_app_cts_c example. I can't seem to find a definitive step-by-step guide as to how to get this working. Any help would...
Hi,
On what occations do the BLE_GAP_TIMEOUT_SRC_ADVERTISING and BLE_GAP_TIMEOUT_SRC_SCAN events fire? The documentation is a tad ... terse .
regards,
Elm
Hy world,
I can update my device with FOTA, but the first time i do:
1 I put: "ble_default_bootloader.hex" on board;
2 i open nrfMasterControlPanel app
3 i write characteristic...
I have a feeling I am missing something completely obvious here. That said, this problem has cost me enough time today that I'm willing to risk embarrassment to see if someone...
I'm trying to implement a simultaneous broadcaster observer by calling ble_gap_adv_start() and sd_ble_gap_scan_start() and waiting for respective events.
If I call advertising...
Hello,
I'm trying to use Eclipse with a Nordic SDK (managed build mode) but it seems Eclipse (latest Mars edition) fails to invoke the assembler. Here is what I found in...
We are looking to use the DCDC to reduce the maximum current during radio operations, but minimize the overall current by enabling it as late as possible before radio use...
I have added button in my project and used bsp_init() to initialize it. All functions in bsp_init() returns NRF_SUCCESS but if I push my button even gpiote_event_handler(...
Hi Folks,
i have implementet a sleep mode by using only the RTC timer with the 32KHz OSC and the WFI instruction. The current consumtion is around 1.7µA (all peripherals...
Hello,
We have some problems with nRFgo Studio on the one of our computers.
Firstly, it takes a long time to flash firmware - about 15-20 seconds:
Secondly, we...
I have interfaced a vibration switch with nRF51822 Pin 19 using external pull-up. When there is no vibration the switch is either at open position or close position randomly...
UPDATED WITH IMPLEMENTATION
Is there a way to know what is triggering a chip boot :
Power off (battery replacement or deffective electrical connection)
The watch...
I have an old project I am trying to recompile for nrf51822 but have been programming with the most recent MDK on my station. The project is asking for old Device Family pack...
Hi all!
I just tried to compile the DFU example from the nRF51_SDK_7.1.0_372d17a and I keep getting the building error:
Referred Memory Range 'IRAM2' is undefined
...
Hello,
Does nRF51822 has a MAC adress when we buy it ?
If yes, is it possible to have two nrF51 with the same MAC adress ?
If yes, can we buy a MAC adress range and...
