I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
I am using the nRF52840, which has BLE support but does not have a touch sensor. Can you recommend a module that includes both a touch sensor and Bluetooth?
I'm now trying to test dongle on nrf52840dongle board：
1. west build -b nrf52840dongle_nrf52840 -- -DCONF_FILE=prj_4llpmconn.conf
2. open nRF Connect for Desktop's Programmer...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
The docu page for the nRF9151
https://docs.nordicsemi.com/bundle/ps_nrf9151/page/ip/radio_lte/doc/frontpage.html
contains a link to
docs.nordicsemi.com/.../intro_nrf9160...
I have customed my own 52820 dongle board.
I wanted to run ncs2.7.0/zephyr/samples/subsys/usb/cdc_acm demo on my board to test whether it worked. So, I builit the cdc_acm...
Hi
I'm trying to make the UART-HCI example run on my nRF5340-DK board.
Environment: - nRF5340-DK Version 2.0.0 (2022.13) - nRFConnect 2.7.0
I've built the example with...
Hi All.
A few years ago, Nordic documentation for developers included many "examples" to practice with and learn about this technology. For instance, ... >examples>ble peripheral...
Hello,
I am in the process of adding LPN nodes to my network, Unfortunately I am getting a lot of "Ignoring old SeqAuth" Warnings and looking at the LPN friendship call...
Hi
i bound rtc in nrf52833 and set/get the time.
but the time is not incrementing ,iam reading the same time which i set.
i added the config below,
but no change in...
Hello,
I am trying to configure P0.9 as output and toggle this pin.
It is no possible but if I change the number of the pin then I can see the modification of the output...
I ran this exercise a month or two ago and it worked to do OTA updates. I then tried recently again and it is giving me "Device not supported" in the Nordic Device manager...
How can I get the lis2dh12 accelerometer speed at 1.344 kHz as mentioned in the datasheet from thingy52?
I have configured the registers as per datasheet of the accelerator...
I tried running the official ranging example with nrf5340dk.
Bluetooth: nRF Distance Measurement with Bluetooth LE discovery
Usage
This example can obtain distance test...
Hello,
I am working on the Raytac MDBT50Q-RX dongle which has the nrf52840 chip embedded. I am having issues programming it using the debug pins on the module, using the...
