Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
Hi,
We are developing a custom hardware that has MDBT42 module with nRF52832 chip on it. Our project is based on the ble-throughput example and this module is using the...
Hi Support,
i did some changes(add some folder ) in gps sample program for nRF9160DK(v1.1.0) and using nRF SDK connect , toolchain 1.7.1, and getting error ( error: Aborting...
Hello
I am working on to flash my firmware binary into external flash by using nrfjprog commandline tools.
I have used below command to program and verify the external...
HI,
I am using BL653dvk board(customized ). I am following this link ( https://devzone.nordicsemi.com/f/nordic-q-a/82430/ncs-external-flash-ota-change-qspi-to-spi ) and...
Hi All,
I usually use nrf Connect for desktop in conjunction with the nrf52 Dongle (nrf52840 chip) to perform DFU's on my devices during development. but recently I have...
To get this example working, both major cellular providers here in NZ, Vodafone and Spark (M2MOne) require a specific (different) APN in order to access their networks.
...
Hi, I want to connect my PC to nRF-52840 through BLE. I git nRF connect for desktop and downloaded the BLE software to another PCA10056 and i managed to connect but i can...
Good morning,
We have a new equipment based on the nRF52840 and s140.
Just now, a new problem has appeared and it is very strange, as it seems to be a ‘random’ error:...
Hello,
I am currently using Fanstel dongle, where I am trying to trigger the USB DFU with nrf connect programmer (buttonless). The example which is provided works on the...
Hello,
I am using an nrf5340dk and I am trying to create a qdec sample using as reference the wheel module.
I have added set the CONFIG_SENSOR and CONFIG_QDEC_NRFX to...
Hello Nordic Experts,
Recently, I have been investigating the radio timing for advertising, I tried to find answers online, but I failed. To explain more clearly, let...
nrfutil is required to program the nrf52840 dongles being distributed at the 2022 Zephyr Developer Summit. west is the tool used by zephyr to install, build, flash, etc. ...
Hi,
I have a QSPI flash device with a weird bug (I think). Basically, when the RDSR command is executed, the HOLD pin needs to be held high otherwise the flash chip status...
Hi,
I'm developing with Segger and nRF52832.
I'm writing a code that makes two tasks into RTOS and sends data to BLE after I2C communication and SPI communication respectively...
Hi, I am using NRF5340 and I want to connect it with a 128x64 oled display with the I2C protocol (Scl, Sda, Vcc, Gnd), I have been trying to connect it for more than a week...
