Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
We are using the QDEC in an nRF52832 and our rotation speeds are 0 to 15rpm, usually around 10rpm. Is there any fundamental reason the QDEC can not be used in this case? We...
I'm trying to get the bmi160 sample to work with my custom nRF9160 board. I think the sample is quite old and not maintained. Unmodified (except fixing pure compilation errors...
Hi.
I am building an I2C driver for the Sensirion SPS30 particle sensor (datasheet: https://no.mouser.com/datasheet/2/682/Sensirion_PM_Sensors_SPS30_Datasheet-1888453...
Hello!
Im trying to change my application. Right now everything works with bonding. DFU and reading and writing characteristics. We have noticed a lot of clients unpair...
Hi all!
I'm trying to run the BLE light switch example on the nRF52833 development board using Segger. I get the following error whenever I try to build the client. This...
sorry where i can find the document/spec for the API that we can use to comunicate with LTE stack L3 . Using Zephyr ? threre are some examples that can help me ?
Best Regards...
Hello everybody, I have to develop an embedded system to acquire and process data. I will be using 2 custom PCBs based on nRF52832: 1- Sensor board: very low power consumption...
Hi Nordic, Please, I am doing a design with nRF52840 and would like to be clear on a few points. Attached is the electrical diagram .
Point 1 For the power supply I am using...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using the RNG functionality with CC310 Library.
When we call this "CRYS_RND_GenerateVector...
Given a 3rd party BLE device (for example a fitness) watch, would it be possible to connect to it using the nRF52 DK and conduct a DFU on it? If so, is there any documentation...
Hi,
I am trying to nrfutil to execute dfu over BLE using nrf52 dk and nrfutil. I have no problems when I try to use nrf_connect mobile app, but I want to use nrfutil desktop...
I want to write my application logs to the flash. I am following this tutorial which is for nrf52: https://jimmywongiot.com/2020/02/24/print-log-flash-log-crash-log-on-nordic...
I want to change the GPIO settings for the pin P1.08 but in the register description (nRF52840_PS_v1.2.pdf) there are only the names and offsets for the pins from P0.00 to...
I've been looking for a DC Motor controller example (for nRF52840) but without luck. Some other users have referred to such an example so I figured it should exist.
Anyone...
I am using SPIM4 with easyDMA in list mode to read a set of registers from an SPI device, and everything seemed to work great until I attempted to use the double buffered...
