Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
Im trying to boot into a custom bootloader following this documentation .
Under "programming the bootloader" it says you must write the bootloader start address...
I have some question about direction finding in BLE5.1.
1. Does the 52840 DK support nRF52811 Soc? if not, Is there any Development kit support nRF52811?
2. Does the AOA...
I called several distributors but they say they don't have a way of differentiating the revs. Please let me know where to order and if needed...how to order please!
Hello there,
I'd like to send and receive data through NRF Radio's handler. I've been able to configure the handler to receive data. Otherwise, I'm having difficulty on...
Hi all, I have some question.
When I using mobile to bond with my DK nrf52832. Infomation will save to flash via FDS library.
So, when I delete bond from mobile and rebond...
Hello
I am using ble_app_multilink_central on nRF52832 DK.
I want to collect advertising data from all peripherals and not connect to them. Problem is that I dont know...
Hi guys! I have had an issue with Image Transfer Demo project. I use nRF52832 with OV2640 camera. I used installation project process described on the page https://github...
Imagine i have a client which sends message to a gateway and i set a TTL for the shortest path . If one of the node is not functioning how will the mesh reroute the message...
nrf52840
sdk for thread and zigbee 2.0
windows
segger studio
in example simple coap cilent and simple coap server
I create my own packet error test through coap...
Hi All,
Currently in my project i'm using hard core delay and delay is custom i.e some places i have used millisecond and in some places used microsecond and in sec.But...
Hi all,
I may need some guidance on the finite state machine method which found an example in app_level.c (from nRF5 SDK for Mesh v3.1), please see my question on below...
What is the minimum specified voltage required on ENABLE (Pin 101) for proper operation of the nRF9160 SIP? Is it the traditional 0.7 VDD, or is it permissible to use a lower...
Hello, I work with an nRF52832 DK and I want to test the example code "ble_app_uart_coexist" . I use the S132 softdevice, SDK 15.3.0 and version 3.1.0 of the mesh for this...
Hi
I used the SDK14 with nRF52832, and carry out the blinky example. When using the Android, the BLE device could be found, but the IOS cannot scan the device. So could...
Hi,
So I am working on NRF52832 with S132 6.1.0 and SDK 15.2.0 mtu and data lenght testings. During that time I was unable to change mtu multiple times while connected ...
