Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi everyone. I want to take advertising data with ble scanner and transmit to esp32 via uart. But I don't know how to do this. Is there an example for this? I need your help...
Hi,
When building a project with nrfonnect , sdk-nrf v1.7.1 that worked for colleagues I got strange warnings:
and the building aborts.
What is very strange is that...
Hello The function scan function is being implemented with nrf52833. The desired action is an action that does not connect immediately when the scan starts, but when you receive...
Using nRF52840 and SDK15.3
I'm seeing some documentation on the DFU process and all that but I'm having to write my own bootloader transport (and lower) layer to implement...
The current PC release of nrfutil.exe, v6.1.2, gives 9 malicious warnings on VirusTotal , including warnings from a couple of the big anti-malware vendors.
I would suggest...
Hi all
I used to use bmi160 for my application with nRF52833 and I am upgrading to bmi270 with nRF52840.
I am struggling to make work the functionalities I used to have...
Hi,
I have an application where I want to send sensor data using advertisement message, and read this message by an iPhone. For test purpose, I am currently transmitting...
Hello,
So, I have a working BLE project on the nRF52840 Dongle and I developed and debugged everything on the DevKit, using Zephyr/nRF Connect for VS Code. From there, I...
Hello, I'm using nrf52832, my own custom board, the UART pins are 10 out, 9 in, no stop bit, no parity and no hardware flow control, baud rate 115200.
Ever so often, in...
Hi,
I'm using SDK17.0.2 example(ble_uart) on nRF52832.When I enabled SPIM to drive sensor,and send data, RTT Viewer logging SOFTDEVICE: INVALID MEMORY ACCESS.
BTW I have...
Hi! This might be non-coherent, I apologize in advance as my knowledge in RF is very limited.
We're developing a sort of 'TX-negotiation protocol' between our peripherals...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
Background - found during testing with proprietry application derived from the 'light_ctrl' sample in nRF Connect SDK, with Time & Schedule Servers added, on an nRF52833DK...
Hi,
i have a question regarding the USART NUS error handler.
In my setup, two Nordic BLE Chips are communicating via the USART service.
One chip is acting as a central...
hello everyone,
i am using nrf52810 with my custom board which contains mpu6050 accelerometer and Gyro-meter so now i want to achieve connectable beacon like it should be...
