I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Hi,
I'm building a gateway using nrf mesh serial, and I want to monitoring devices status in the network by listening heartbeat messages from devices, but when I set publication...
Dear All, We will do a production with over 1000 Nordic nrf9160 devices, for which we need to program the modem firmware (v1.2.0) and the application software. We would like...
Hello, I started learning BLE/nrf about a week ago and I faced an issue that I unable to handle more than one connection simultaneously.
I have a pretty simple application...
Hi,
I am using nRF52832 and SDK v15.00 for development.
I am working in ble_app_uart peripheral example. I have a task where I need to configure another UART communication...
Hello Everyone,
we are using Nordic's nRF52840 controller with SoftDevice S140 and the default Bootloader(C:\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10056_ble...
Hello, I am working on a nRF52840 and started with the SDK15 gls bonding example. The device has no buttons or display so we are stuck with 1v2. We are hoping to incorporate...
Dear friend，
I want to implement ota data packet request through my own code. In the \examples\zigbee\ota\client example, line 876-1268 of zb_zcl_ota_upgrade.h finds the...
Hi there,
I'm using a nRF52-DK for a while, but now I made a bad misstake: overwrote the interface firmware. I pressed accidentally the RESET button and flashed a wrong...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
Hi all,
I have two questions about BSP buttons management.
I see that the BSP supports the short press and long press for a button. However it seems to handle only one...
Hello
I want to read the values of two potentiometers from the Ain0 pin and the Ain1 pin through SAADC.
I could easily read one value through the saadc example, but I...
Are you able to enable internal pin pulls for UARTE pins, specifically the selected RX pin?
On page 490 of the nRF52833 datasheet, footnote '35' states that "High baud rates...
Hi Nordic Team, I have been working a project where I will need to send audio using I2S protocol to an audio chip. The audio chip will only accept a select set of values for...
Hi
We searched a lot of stuff regarding FOTA update in nRF52840DK using Lwm2m and coap protocol. But we could not get help in the right direction. We could not find any...
