Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
my central application is scanning for, and connecting to, only a single pre assigned peripheral device/address.
This central device is used in a high RF/BLE peripheral...
Hello all.
My product uses nRF51422 and S310 v3.0.0 SoftDevice on EYAGJNZXX by Taiyo Yuden.
When I submit the test plan, I can't find any tested component of S310 v3...
Hello, I've downloaded the lastest SDK (ver. 12) and the installer is only valid for keil 4.
Is it any option to have this SDK working on keil uvision 5 ?
Thanks in...
Hello all,
I just bought the nRF52(PCA10040) DK and programmed the s132 version 3 soft device using nRFgo Studio. Using IAR, I compiled and downloaded the UART example...
Hi,I'am try to update the bootloader. But it stop at 1%. I don't what I miss.
james_boot.hex
james_bootloader.zip
Log 2016-09-06 11_36_54.txt
Dfu_bootloader_via_hex...
hello,
I'm using S132/nRF52/SDK11.
I start a firmware development based on Nordic UART example, I kept the BLE NUS part (I loop back the data received over BLE) and...
Hi All,
Just noticed SDK12 was released last week, with build in support for S132, v 3.0.0. Judging from the compatibility matrix and notes, it looks like it removed support...
Hello,
I'm trying to set a new environment with the SDK12 that'll be less cringy than the one I was running under the previous one.
Basically, what I want is a workspace...
Hi
Using an nRF52832 and SDK11, I have the following issue:
I want to use button 0 with a regular push for functionality and a long press to go to sleep. The detection...
Hi, I'm trying to move from nRF5_SDK_11.0.0_89a8197 to nRF5_SDK_12.0.0_12f24da and faced an issue. I have build error in
....../nRF5_SDK_12.0.0_12f24da/components/libraries...
Hi@all,
i'm trying to connect to a BTLE Printer (printer -> peripheral) from my central (nrf51822 board). But i cannot use the standard discovery examples because i cannot...
Hello, I have pca10001 board and I would like to read an analog input from ADC.
Is there any complete example which I can test using potentiometer ?
Thanks
I'm trying to write some data to flash memory (32 bytes) every 1 minute. the data are not NULL but then I noticed that sometimes (not always) the pstroage module write zeros...
Hi,
I am programming and debugging an external customised board by following the DK manual and the below link:
electronut.in/.../
I use the interface P20 instead of...
