Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
I recently upgraded from SDK 11.0 to SDK 14.0 and am seeing much slower connection speeds from the new SDK. The old version would connect in about 400ms, but the new SDK takes...
I would like to measure the VDDH voltage (lithium ion battery) on a nrf52840 with the power fail comparator.
If the voltage drops below the threshold, I want to reduce the...
Hi all,
we are using NRF52810 and SDK 15.0 (our own custom board)
working on ble_app_uart.c example.
we are able to send / receive 20bytes(approx).
we need to transfer...
In my project, I aim to send an ADC value (10 bits ADC) and 6 data (16 bits/each data) from MPU6050 by using nrf51 DK to Android app ( modified from https://github.com/NordicPlayground...
Hi,
Using the nRF52832 device with the S132-v4.0.2 soft-device (s132_nrf52_4.0.2_softdevice) (So customized that two nRF52832 devices with the same Soft-Device interact...
Hi,
I do the FreeRTOS Blinky sample, works fine and I do the BLE Client/Server sample, works also fine.
Is there any sample combining FreeRTOS with a SoftDevice (132 for...
Hello,
I referred a Softdevice 130,310 & 132 Specification, from where i noticed that softdevice includes Host & Link Layer (As a part of Controller).
So, i want to ask...
Hello,
I'm working with 3 servers, 1 client and 1 provisionner ( 4 nRF52832-DK + 1 android with NRF Mesh App ).
Client side : light switch proxy_client example Server...
hi!
I use the reference design of nrf52832_ciaa.IntLib ,but it didn't work
I use the internal-LDO ,but i measure the voltage of DEC4, it's 2.5V(not 1.3V), the VDD is 2...
Hello,
I am developing a BLE application using the custom characteristic example provided by nordic. I have added a few characteristic for the same.
I am having a small...
I am just trying to establish communication between spi master and spi slave.
I am using two nrf52 boards, SDK 15, in one i dumped spi master example and in another i dumped...
Hi,
I have a customer developing with the nRF8001 with an external MCU, a PIC32MM. He is interfacing the the device with SPI and he is struggling to set up the device and...
Dear support team,
I'd like to provision a mesh node which is implement on thingy and without proxy feature.
As I know, the BLE device (mobile) should communicate with...
hello I am new on nrf52 and I would like to run the example for the ant+: "bpwr_tx".
I am on a nrf52832 chip (with a pca10040 1.2.4 demo board ), I am using nRF5_SDK_15...
