If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
Currently I am searching for s130 example code. I know it's in alpha stage, but I think it should be possible to start to experiment with it, isn't it?
In the past I've...
Hi,
I tried following code to close the ANT+ channel on channel not connected to the other ANT+ device:
#define CBSC_TX_ANT_CHANNEL 0
void ant_adv_timeout_handler(void...
We have a DFU which uses a different set of of services than the main app.
Both of them share bonding information which is create by our main app.
Once we switch to DFU...
I am trying to build a system with a single PRX and up to 5 PTX devices.
Initial development work was done with a single PTX with it's address on Pipe0 in the PRX. I have...
I have a CC2540 and CC2541 chip with me. I did figure out that both of them are working, but now I am stuck up at how to practically test if the proximity profile is working...
Hi,all
I want to simulate HFP(Hands-Free Profile) on S110, and i know HFP is one profile of Classic Bluetooth.
If i implement HFP on nrf51822, it can work will?
How would you go about extending Gazelle ?
For example I have a host with four devices. I want to connect this host to another host with its own set of devices.
Hi,
I'm planning to use a nRF8002 to transmit via BT the state of a pushbutton to a RFduino. I've my RFduino ready to receive data (and this works when paired to my iPhone...
Hi,
I'm trying to detect the nrf8001 by my Mac. My android device detects it, but when I search for it in mac, it's not detected.
I'm using this library: github.com...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I recently started working with the NRF51822 and PCA1001
I need to read data from MPU9150 accelerometer via I2C and transmit the results over BLE.
I connected the...
Hi,
I'm communicating ANT through softdevice ant event handler as follows:
err_code = softdevice_ant_evt_handler_set(on_ant_evt);
void on_ant_evt(ant_evt_t * p_ant_evt...
Hi,
I'm using PCA10003 board with nrf51422 chip with version E0 and tried connecting ANT with ANTware II software using the HRM example and it works fine on UART but on ANTware...
Hi,
I'm using BLE and ANT+ concurrently with nrf51422 and s310 softdevice. I'm using on_ble_evt for BLE and on_ant_evt for ANT+.
I'm using following code for advertising...
Hi,
I want to add a bit (about 100KB) off data to my project in Keil.
I need to work out where to locate it (to avoid my code and the S120)
I can't seem to find a memory...
