Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
For my application I am supposed to evaluate if nordic SPIM & SPIS drivers are working on interrupts..? In the driver file "nrfx_spim.c" I observed the below code...
Hi,
I have some questions regarding DFU:
Does it have its own BLE hardware?
Does it have its own processor? Or it's part of the main one?
Can we synchronize between...
Hi all,
struct spi_config {
uint32_t frequency ;
uint16_t operation ;
uint16_t slave ;
const struct spi_cs_control * cs ;
};
in documentation, it says...
Hi I am recently working on Enhanced Shock Burst (ESB) protocol. where PTX and PRX
and
PRX will communicate upto 8 PTX
i have a question like how a single device will...
I'm working on porting some Arduino code for a Crystalfontz 320x240 FT810 display to run on the nRF9160DK. I'm having some success, But it seems Zephyr has an FT8XX driver...
I use a example application from SDK_DIR\examples\ble_peripheral\ble_app_template\pca10056 base on nRF5 SDK v17.1.0,then use SDK_DIR\examples\dfu\secure_bootloader\pca10056_s140_ble_debug...
Hello there, my application needs to switch master/slave roles after the connection established.
As i know, the initiating device will be master every time in BLE. From...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a characteristic using characteristic_add. I want to set the attribute handle...
Hi
1、 A customer wants to evaluate the keyboard that can run ble and mesh simultaneously with nrf52 chip.
2、I found mesh example in both NCS and nrf5_SDK_for_Mesh_v5.0...
Hi, I am working on this project where provsioner provisions all the unprovisioned devices (nodes) and then sends the LED's data (containing brightness, intensity and pattern...
Hi, I tried running an spi sample program with code as in below, shorted the MOSI and MISO pins and data was visibly received in print statement:
While in the same code...
I have recently bought nRF9160-DK on Mouser, here's the product page: https://www.mouser.ie/ProductDetail/949-NRF9160-DK
On Mouser, it is marked as LTE-M NFC NBIOT GPS &...
In an attempt to do in app DFU I have taken the following resources for inspiration:
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_uart_debug
and the...
