I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hi, I was trying to interface nRF 52840 with a SPI based NOR flash (IS25LP064A). I am using SPI example in 16.0.0 sdk version. But i am not able to read the device id as this...
Hi,
I use SDK15.3
There's no such define in "ble_gap.h"
Is this define "BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED" only S140?
Because 52811 use...
Segger Embedded Studio always starts with license error even though a nRF52840 DK is connected.
It always complains as follows:
"
Embedded Studio could not find a commercial...
I'm getting an undefined reference to "app_uart_init". I've enabled the respective libraries in the sdk_config.h:
//====================================================...
I tried to combine the Wireless_uart example with the USB CDC example to be capable of using both but it doesn't seem to be working.
When I plug my board using the nrf USB...
Hi there,
I am using WIN10, Segger studio 4.52c and nRF SDK16.
I can successfully run ble_app_uart example on PCA10056, but when i try to run same code on fanstel EV-840...
Hi, I have been working on setting up the environment for development of nrf52840 and nrf9160 the past three days. I have nRF9160 dk which comes with nrf52840. I have been...
When I built and run your example Bluetooth: Peripheral HIDS keyboard and I saw the following errors in logs: E: set-value failure. key: bt/ccc/283926aaa86c0 error(-2) E:...
Hi,
We would like to know whether below gang programmer can be used for gang firmware flashing of NRF9160 application FW and NRF9160 modem FW.
Also we would like to know...
I am getting the following error when trying to register a nRF9160-DK with a HWID. There was an error adding your device: nRFCode 40001:
Please advise how to move forward...
Hello!
I've got a couple of NRF52832 based modules - Holyiot-17095-nRF52832. These modules are presented in the list of supported - https://www.nordicsemi.com/Software-and...
I performed below mentioned steps:
Downloaded SDK 12.1.0
Soft Device s130_nrf51_2.0.1_softdevice.hex
Built secure boot-loader with new public key
Built project ble_app_hrs...
I'm trying to compile hci_usb sample of Zephyr with Nordic Connect SDK v1.3.0 using Nordic's proprietary controller but apparently it fails.
I'm using following configuration...
Hi I'm doing the Bluetooth GATT: How to Design Custom Services & Characteristics [MIDI device use case] example ( https://www.novelbits.io/bluetooth-gatt-services-characteristics...
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer. My setup: HW: PCA10040 1.2.4 SDK: 15.3 Project: \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral...
