Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
Hello,
We are currently working on a project where we need to sample a frequency input on a GPIO pin up to 6MHz. I have tried GPIOTE and TIMER with a PPI channel, but can...
Hi
I am reading the exernal power in one ADC channel and the backup battery in other ADC channel. When my hardware has not external power and the backup battery drop until...
Your old documentation website ttps://infocenter.nordicsemi.com/ carries a banner saying it will be shut down on 18 June 2024. Please don't do this! I can't find equivalent...
I'm running NCSv2.6.0 on some custom hardware, with an nRF52832 IC fitted. I'm trying to trigger an ADC measurement every ~ 300usec using a Counter, so need to set the Counter...
Hello community,
I am working on a custom nrf5340 board design, that uses the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
You may ask what poolside means. It means at my community pool, where I don't have Internet access via Wi-Fi for my laptop.
I wish to run some AT commands like AT%NCELLMEAS...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
I'm confused about the use of these two functions. I want my app to sleep immediately upon start and then wake up and do a BLE advertise when I press a button.
I...
Hello everyone,
I've been spending a lot of time to fix the issue not being able to enter DFU mode with the following error. I've changed so many versions of GCC, but it...
Dear Nordic devzone community,
I have designed a custom board using nRF9160 and I am able to send and read out certain AT commands which confirms to me that most of the...
I'm transitioning from SES to Visual Studio Code.
In SES, I can define multiple builds and then define preprocessor options (eg. -DOPTION1) for each build definition
I...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
