When migrating form NCS 2.5.0 to 2.7.0, some of my PPI + GPIOTE code just stopped working. To debug this issue, I have added print statements after the PPI alloc function...
I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello All,
I have nrf9610 Develoment Kit on my side:
mfw_nrf9160_1.3.5
Using nrfutil-device core version: 7.13.0
Using nrfutil-device version: 2.1.1
...
I am developing an MQTT client application with NRF9160, trying to connect to a Mosquitto broker using TLS with three certificates. However, I am encountering an SSL version...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
Hi,
I'm trying to setup my NFR52840 DK to act as a NFC tag so that I can read some simple data on my phone via NFC transfer.
I have tried a few NFC sample applications...
Hi,
I am using a modified HTTPS Client demo code [Let's say Version A] and sometimes when trying to debug with Segger Embedded Studio for ARM (Nordic Edition v 5.34a/Jlink...
Hello,
From time to time I am getting the error " Unable to find bootable image" when I start a debug session in SES-NE v5.60.
FIH_CALL(boot_go, fih_rc, &rsp); if (fih_not_eq...
I am trying to read the GPIO state on an nRF52840 right after it wakes up from deep sleep (System OFF mode). I have configured 4 pins as wake-up sources from deep sleep System...
I have been working on finding the cause to an unexpectedly high power power consumption in several newly produced units of our product based on nRF5340. I believe I have...
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection processing between the Gateway and Headset take place?
2. Where is the BLE...
I'm trying to build a custom secure partition, but get the following error when building:
However when navigating in files to the directory the file "tfm_custompartitiontest...
Hi All,
My team recently reserved a custom service UUID with the Bluetooth SIG, and we'd like to replace the custom 128-bit UUID we had been using in our products. Can I...
HI
We are mass producing NUS-based products.
During mass production testing, pairing is performed and functionality is tested by pressing buttons, etc.
However, pairing...
I'm using
AT_MONITOR ( catch_all , ANY , on_modem_at_notification );
and I'm just printing the notification on reception:
static void on_modem_at_notification...
Hello,
I would like to add to my project new i2c slave (for example - dac5571 from TI). In the DTS overlay - under the i2c0 node I need to specify compatible , and I don...
I have configured the nrf52840 DK one board as Peripheral and other as central.
Added multiple services and characteristics. I am sending some data at every 20ms using notify...
Dear all:
Customer products in normal mode, BLE works normally, all functions are OK. An error occurred in DTM mode during authentication. Procedure The failure status is...