I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi, I have a NRF52840 DK. I want to use ble_app_uart_c and my peripheral is NRF52840 Dongle and also I want to receive and transmit special frame over ble. I have a problem...
Hello Nordic engineer,
I used SDK15.3.0 and nRF52811
I want to ask three questions,
(1)
Can a session be opened forever?
I will frequently use BLE+ESB in my...
I am trying to build the example for the Audio DK on an x86 Mac and am having trouble configuring the toolchain. I have followed the instructions from here: developer.nordicsemi...
Since the previous topic was closed by accident and not able to reopen again, I will continue here.
Menon said:
Sorry I didn't get you well. You are using nRF5 SDK just...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Segger Embedded Studio 4.16
Aim: Controlling...
Hi ,
I have added simple on off mode in my previous application which was based on Generic ON OFF model. Code for simple on off model is added in both server and client...
Hello,
I have on nrf5340 an application, that meassures Temperature every second. I need to send the data to another nrf5340. I am going throw the bluetooth samples, but...
Hi
I'm trying to configure zephyr to build BLE host on the application core and BLE controller on network core on the nrf5340dk.
I was able to configure zephyr to run...
Hello,
I've been having issues trying to add MCUBoot to our application. The app is based on the Common Application Framework (CAF) with a structure based on the nrf_desktop...
hi,
sdk 17.1.0
Can I call " NRF_LOG_INFO" API back to back ? Does it copy the contents of the buffer (var) to an internal buffer ?
For example, in the below code, does...
Hi,
I am using nrf52833 ic with zephyr for firmware development my product is a battery based device and i want to reduce it power consumption when in ideal state what are...
Hello all,
I have pinged the sensor on the "twi bus" successfully, now I am following the post on the read/write function that is needed to actually read the data off the...
Dear nordic engineers:
The only example I can find about flash is under zephyr/samples/drivers/spi_flash. However, the flash writing is pretty slow, and the MCU is halting...
I'm trying to record audio from Nano 33 BLE Sense which is using an nrf52840 microcontroller. But the default PDM library available doesn't allow me to record at a higher...
