I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello,
I am successfully able to open and close adapter for nRF52840 using pc-ble-driver-py using python3.6.0 on my host armv7 Linux board.
But doing same inside the docker...
Hi,
We are developing BLE firmware that will allow BLE pairing without bonding (but with PIN/Passkey that is entered from the phone). However, when I try this with nRFconnect...
Hello Nordic Support.
I would like to build and use a Sniffer using a PC (Windows 10), nRF52DK, and nRFConnect for desktop.
Please teach me about the following.
nRFSniffer...
Hi, I can successfully build the Matter light bulb example in nRF Connect SDK 1.9.1 but I fail to do the same in v1.9.99-dev1.
What did you change?
Here the error:
west...
Dear DevZone support team
I'm facing the following problem: My application uses the Zephyr's BLE stack and basically does not much beside parsing JSON-messages received...
Hi,
I tried to implement PPI for a very timing sensitive application. The sample PPI_trace uses the RTC but it is too slow for my application so I'd want ot use timer0...
Hello,
We would like to use BLE to transmit a lossy data stream at high data rate. Looks like Isochronous channel is the best choice. How's the Isochronous channel is...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hi,
I work on an AOA projet and i have a problem.
I have already made a transmitter (with an nRF52833) and a receiver (also nRF52833) and i can see the CTE send by my...
I need to add a custom BLE service with over 20 custom characteristics. During the gap nitialization step, I set the BLE security mode and security level like this:
sec_mode...
Hi ,
Am following the below link https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t-build-pass ,
am able to build it for...
hello,
i am using nrf52832 with accelarometer i want to put my board in shutdown for current consumption for that i am giving this command sd_power_system_off(); whenever...
I need to be able to change the device name the SoftDevice uses AFTER the soft device is up and running. To change the device name, To do this I use
errorCode = sd_ble_gap_device_name_set...
Hi,
I currently have a macro in the nRF Connect Mobile app (Android) that displays RSSI every time I receive a temperature signal. I am saving the logged temperature and...
It seems that not all UICR registers are erased on this nRF52840 chip
nrfjprog -f nrf52 --recover
Just make sure one more time:
nrfjprog -f nrf52 --eraseuicr
nrfjprog...
