We are planning to use the nRF54L15 for a Matter over Thread product, so we are currently evaluating the low-power performance of this device.
According to the nRF54L15...
Hi everyone,
I’m trying to program/recover a custom board with an nRF52840 Fanstel module using a Nordic nRF52840 DK as the programmer. The board is powered from a 4.2 V...
Hi Nordic teams,
I am working on integrating single-slot DFU for the nRF54H20 based on the throughput example. However, I noticed a difference in how the Bluetooth controller...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi Nordic
I am wondering whether one device can connect to two Bluetooth devices at the same time and independently control the TX power to communicate with the two devices...
Hi,
When starting nRF Connect for VS Code, SDK v3.3.0, the message Unable to resolve configuration with compilerPath: "C:\ncs\toolchains\fd21892d0f\opt\zephyr-sdk\arm-zephyr...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
hi,
i am working with nrf52832. system on sleep mode is working ok in ble_app_uart example by commenting " //err_code = sd_power_system_off(); //APP_ERROR_CHECK(err_code...
I'm guessing this isn't the best place to ask this question. Please redirect if you can suggest a better place to ask. Thanks! I'll recopy the question here:
NRF has an...
Using
SW : NRF_SDK_16, SDK_MESH_v4.0
HW: NRF52840 DONGLE.
I have implemented light_switch_client which also has USB part initialization and then added in USB_DONGLE...
I am working on the nRF5340DK and NCS v1.5.0
Acording to this example https://github.com/NordicMatt/multi-NUS , I used the Throughput sample as the fundermental project...
I'm measuring the power consumption of the BLE Beacon example and got the graph below for one beacon transmission. I'm wondering what those smaller peaks are with 1ms period...
Howdy,
I'm evaluating the nRF Sniffer + nRF52840 dongle as a stop gap BLE sniffer solution, but I'm having a lot of issues setting it up.
Re: Installing nRF Sniffer (...
Good morning,
I am working with the AOA module of the nRF Connect SDK. I have been able to configure and program the transmitter with the CTE as well as the receiver and...
Dear Nordic,
we are developing an application based on SDK 17.0.2, it user FreeRTOS and BLE with Peer Manager.
We need to store few data in FLASH without confict with...
Hi
We are trying to get the DTM mode working for the NRF52 2nd BLE for testing BLE TX power and RSSI at the factory.
(1)HW setup is shown
(2 ) Procedure
We have...
Hello,
what are necessary that a Device automatically (without a 3rd party app) connect to the GATT Server with a HID Service.
I have implement a
HID Service,
Device...
hi，
I'm use nRF52840 to developing a Computer Keyboard，i wish 8X18 matrix a total of 144 buttons，About keyboard button matrix, please help to determine which GPIO can do...
Hello,
I am trying to resolve some compliance issues with the third-party libraries that are used in the SDK. For nanopb, it seems like the changes in pb_decode.h mentioned...
Hello,
I want to configure pin 0.13 as a rising edge interrupt.
Is there any sample code to configure the pin and interrupt handler?
Thanks in advance.
Hello,
In a previous post I asked about scanning and connecting based on specific advertised data. After some testing I realized that my two nrf dks only connect sometimes...
