Hi,
We have two option to use Flash memory,
Option 1: We are planning to use Flash Memory on the SPI bus shared with the NRF7002. Kindly confirm whether this configuration...
Hello,
We are currently performing power consumption measurements on the Nordic nRF9151 using the PPK2 in LTE-M with an Objenious SIM card.
During our tests, we observed...
Developing an implementation for UltraWideBandImpl for a different UWB hardware solution (not the provided qm35 implementation) and running into integration problems
The...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi, Iam working on creating a ble mesh network. I wanted send led status whether on/off message from server to client periodically like every 10sec. I have configured the...
Hi I'm learning Zephyr ecosystem in context of using nRF SoCs. How one can achieve current consumption values as low as in datasheet ( 0,4 uA in System Off, with no RAM retention...
After nrf52840 uses the SPIM3 peripheral to send data, turn off the SPIM3 peripheral to enter low power consumption, and there will be 700UA current; if the SPIM3 peripheral...
I am trying to read data from a chip over SPI.
The implementation of the SPI comms is not ideal as they require a new CS/SS line toggle on every byte. I cannot do a bulk...
I hope that someone can show a clear example of this. I surprised that it isn't in the SDK examples. Basically, it is necessary to stop the BLE SD, in most low-power examples...
Hi,
I am having a problem where the client is unable to receive notification from a peripheral after the softdevice in the peripheral returns 0x3002 after a disconnect....
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
I am Rattana. I have some project for Bluetooth communicate with mobile phone. Then I will use BC805M(nRF52805).Nomally I connect my MCU with HC06 and I use MCU because I...
Hello I'm now trying to implement the IOS Phones (Central) - Device (Peripheral) liver UART using Multiple Connection - Nordic Uart Service. Devices tried to send a UART signal...
Hi,
We are following the project CHIP and planning on design a matter device with our existing hardware platform. The below are some questions about it:
1. Our platform...
Dear Nordic Bluetooth Experts,
My project is quite simple: A BT Mesh device (generic level server model) powered by a Nordic nRF53832 and an Android app that is used to...
Hi Everyone,
This new way of doing firmware seems to have taken such a turn from what I've been doing for the past 20 years that I don't know where to begin. All I'm trying...
Hello,
I am using android nrf mesh app as a base app and using the latest nrf mesh library version.
I am taking provisioning trails on inline on-off controller.
While...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from nrfconnect mobile app but iam able...
