We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
I need to create a health device that sends time stamps of the measurement. For that to work I would need the counter to continue between power cycles. Some devices have a...
When the program runs, it will enter the hardware fault，because part of the code is lost in the program storage area of flash.
As shown in the figure, the left part is...
I want to implement lwm2m, and I use nRF Connect SDK v1.4.99-dev to compile the thread firmware.
I am using 52840DK, here is a screenshot of my project creation
No code...
Hello,
I had encountered framing errors when running automated tests that utilize UART CLI in my main code base. Currently what the test does is it sends a CLI command...
Hello,
I am using a nrf5340pdk board and I want to connect a sensor using I2C.
Which pin numbers of the board can be used for the SDA and SCL connection?
Do I need to...
I'm transitioning from nRF5 SDK to NCS and using Segger Embedded Studio (SES).
When using nRF5, SES gives options for the Compiler, including saving the Preprocessor output...
Hi,
I'm getting an error while trying to update the modem firmware (mfwnrf9160121.zip) on my thingy91.
I'm using nrfConnect Desktop on Windows 10, I activate DFU mode...
Hi. I am currently using the nRF52840 DK board and using the SDK 17.02.
There is our software engineers who are working on the heart rate service app to modify to suit our...
Hi,
I just got Thingy:91, and I was trying to see the response for a simple hello_world (found in zephyr\samples) application from Thingy:91.
Thingy:91 got programmed...
Hi,
Are LTE-M efficiency/TRP/TIS results of the nRF9160 DK on-board antenna available? In case there are several DK revisions available, does the version affect antenna...
Hi,
I am trying to understand how to enable SPI in blinky application provided by Nordic. My intention is to transfer data between the two Nordic development kit running...
I have advertising in s130 set to BLE_GAP_ADV_TIMEOUT_GENERAL_UNLIMITED. The idea is to advertise until a connection event is received. In reality the user will pull the finger...
Hi ,
1. I learned from Nordic FAE that on the nrf9160 module, 10 minutes after the edrx mode, the nrf9160 module automatically powers off the sim card to save power,
2...
