Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
We are implementing a DFU controller to perform DFU over serial for the nRF52832.
Our reference is the nRF5 SDK v15.3.0 DFU Serial documentation (Nordic/SDK/nRF_SDK_15.3...
There are a few threads on here about this already, but I wasn't find the answer to the exact question I had.
I am using the nRF52832 with SD132 and SDK15.2 on a custom...
I cannot get logging in the Seggar debug terminal nor the J-link viewer application (All terminals) when running this example.
I have the NRF_LOG_BACKEND_RTT_ENABLED selected...
Hello
I am using nrf52840 from nrf9160dk, I am trying to run example from nrf52840 with sdk16.0.0 and sd7.0.0. While checking data on uart I am getting following error...
Hi
I'm trying to get a DFU boot loader working on our own custom hardware. My initial approach was to build secure_bootloader_ble using my own public_key.c file and try...
I updated my Thingy:91 today to version thingy91_fw_2020-04-29_bc7ade8b.
I flashed the mfwnrf9160120, the thingy91_nrf52_connectivity_bridge_2020-04-29_bc7ade8b and the...
Hi, I'm developing firmware for the trf7970a nfc chip. For standard communication the chip uses spi, but a special direct mode uses an additional two wire interface where...
Do the values for current consumption given for the scenarios in Section 5.2.1 of the nRF52833 PS include the current for any peripherals required? E.g. the PS quotes 2.6uA...
Hi!
I am trying to merge the basic/button sample with the mqtt-simple sample.
I added to the prj.conf of mqtt-simple sample.
My main.c looks like this:
After merging...
Hello!
Iam trying to get the spi function to work properly on my thingy 52 device.
My problem is that the transfer wont stop when it should in my opinion, i have analyzed...
Situation: SES, SDK 16, nRF52832
I'm developing a pre-production test program without BLE. I'm using APP_TIMER_V2 and noticed that the timer events do not not happen even...
We have a custom board with nrf9160, ncs 1.2.0 and modem fw 1.1.1. We experience strange behaviour with the GPS: As an example,on units with 30 min fix intervals, we experience...
I added the commissioning part from the nfc_meshcop example to the mqttsn_sleepy_subscriber example. I tested the nfc_meshcop exaple and worked, so the border router part...
Hi,
I have developed a project of mine based on the nRF52840 DK and now I want to place
the nRF52840 chip on my custom 2 layer PCB board but I think that it might be very...
We still have some Problems to use the Supl client Library, to test it we use the normal GPS example and seems like the connection is available with NB-Iot settings. We are...
