Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
What all do I need to modify in the Blinky peripheral (from SDK 16) with in order for the 840 DK to advertise and connect with CODED PHY in long range mode?
My code compiles...
Hi everyone,
I am looking at using MQTT v3.1.1 with TLS 1.2, to send data to Azure IoT Hub.
I tested the MQTT Simple sample and it worked perfeclty. So I am modifying...
nrf52832 , I have flashed ble_peripheral/ble_app_uart with simple modifications
ble doesn’t advertise while Jlink/seggar debugger is connected to our custom board.
...
I use SDK16.0
use BLE + Multiple Beacon, Beacon use timeslot,BLE use softdevice.
I want to modify the advertising content of BLE,But use advertising_stop->advertising_init...
I'm currently working on integrating modem FOTA updates into my application. I have the FOTA working at the moment, I'm able to go to and from a FOTA-TEST version with the...
I try to run this sample https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/mqtt_simple from the master branch, but when I connect to the network...
I'm connecting the battery to the VDDH 3.6V or 3.7V and sensor to VDD, it means nrf52833 get powred on from VDDH and sensor get the power from VDD. is it ok? please check...
I use the nRF52840 MCU and SDK 16 with S140 softdevice. I want to use spi interface to control 3 SPI slave. They share the same SCK, MISO and MOSI. I use 3 chip select pis...
We're using the IOS-Pods-DFU-Library on an iOS13 iPhone connecting with an embedded device that supports Nordic NRF DFU. We're experiencing some issues with both the nRFConnect...
I have questions related to use of UUIDs. Any help would be grateful.
The following are the UUIDs that are seen from our peripheral device during advertisements and after...
Hi,
I tried to use the exactly same code in the TWI scanner example for nrf52832, SDK15.3. Everything works fine when I flashed only the example code, which has no softdevice...
I am looking for an updated schematic for the PCA10059 v1.2.0. Everything on info center is version 1.0.0. Noticed that a resistor was added (R7) so wondering if there were...
I'm trying to debug issues in my application related to FDS garbage collection.
My application periodically runs fds_gc() from startup. At this point, garbage collection...
Hi
I got a nrf52833 dk and followed "nrf52833_heart" SDK file readme file is success
next step I install segger studio and JLink_Linux_V662d_x86_64.
wend i open studio...
