Hi support team,
We would like to evaluate channel sounding using your evaluation board.(nRF54L15-DK and nRF54L15-TAG)
We have been able to verify channel sounding using...
Hi all,
I want to ask which silicon version are the DK stocked at Mouser or DIGIKEY for the product nRF52LM20-DK. Is it version 0.7.0? Thanks!
2.16.1.2
2.16.1.2
2...
Hello!
We have a nRF52832 firmware project on NCS v3.4.1. After recently moving from NCS v2.9.0 we saw small current spikes every 1s (roughly) in our idle state, which weren...
Hi,
I'm sending IPv6 traffic between two PCs over a DECT NR+ link: two nRF9151, one FT and one PT, NCS 3.4.0, modem firmware mfw-nr_nrf91x1_2.0.0, using the l2_dect stack...
What high-temperature storage (JESD22-A103) and temperature-cycling conditions was the nRF9151 qualified to (temperature, duration, cycles)? Your DevZone forum mentions 125...
Hi,
I am experiencing an intermittent issue with the debugger in nRF Connect for VS Code version 2026.9.2823 on Windows.
Environment:
nRF Connect for VS Code: 2026...
Please tell me. The NRF24 transmitter is in the one pipe in channel one, sends data to the receiver without confirmation of delivery at a speed of 250 kbps. 1 How long will...
Hello.
I need some documents that i can understand what is going on on the backward when/while two devices are communicating with each other or when/while a device advertising...
We're just finishing our layout for a custom nRF52832 board. According to the "General PCB design guidlines for nRF52 series" we copied the complete nRF layout from your reference...
We recently purchased a few Thingy 52s, and we're very impressed with the simplicity!
After playing with the Thingy 52,and upgrading the FW to 2.2.0, I noticed that the...
I linked to an external lib library and called several of its functions，Then compile and report errors；It seems like the compiler could not find the definitions of “__aeabi_memclr4...
hi Support team,
Our customer is using usb cdc asm as one additional UART port to communicate with PC, one question about this : is there any reference code for our customer...
I want to repeat that everything worked great in 1.2.0.
------------------------------------------------------------------- --------------------------------------------...
Hello,
I'm using the OpenThread from v4.0.0 of the Thread/Zigbee library and the TEMP driver to read nRF52840 temperature via a nrfx_temp_data_handler_t. I noticed the handler...
Hi,
I am trying to perform Buttonless DFU on a nrf52832 chip. I am using SES on Windows. I do DFU with nrfToolbox on my iPhone.
The way I do it is by packaging the DFU...
Hi,
I am trying to setup L2CAP channel in ble_app_uart. I referred the object transfer example and did the initialization of L2CAP parameters during ble_stack_init() both...
For certification purposes to qualify for the QDID defined by Nordic , are there any characteristics that are required to be present in the Device information Service (System...
Dear nordic team,
I'm developing a sensor based on nrf52840 and I want to make use of CMSIS NN. I have already integrated CMSIS in my eclipse project and can already use...
Hi,
Here i am reading the temperature data via i2c protocol , where the temperature sensor is connected to the nrf52832 .(15.2 version sdk) Now i want to publish the temperature...
I'm using nrf52840 with nRF5_SDK_17.0.0_9d13099 and usbd_audio loopback example. The example works fine with the given hex file but when i compile it myself, the signal seems...
