Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I see the SWD debug port is a 2-wire protocol, SWCLK and SWDIO. My debugger device has two additional pins, SWO and nReset. Are these two pins required to debug and program...
I PURCHASED A SIM OF THE THINGHS MOBILE BECAUSE IBASIC DOES NOT WORK.
I HAVE LAUNCHED ASSET TRACKER AND THE NRF9160 DOES NOT CONNECT. LTE FLASHES IN YELLOW.
IS THERE A...
I was checking DFU through serial usb/uart on the following link:
infocenter.nordicsemi.com/index.jsp
I want to double check if this entire project is for programming...
Hi,
While linking I am getting the following error on Nordic SDK 16.0,
XYZ.axf: Error: L6218E: Undefined symbol nrf_ble_gq_conn_handle_register (referred from ble_db_discovery...
Hi everyone,
I am new to segger embedded studio. I want ibeacon firmware sample code to advertise uuid, major, minor, tx power, advertisement interval. I want to change...
We're developing a product where a single NRF52840 board - lets call it the central- serves as the focal point for multiple NRF52840 boards spread out across an area - lets...
I am not able understand the difference between APPROTECT and BPROT . Can you please clarify ? and if we enable the protection then how to disable it again whenever we want...
I've seen many posts about LL_LENGTH_REQ causing disconnection on certain Android phones and the solution from Nordic is to add a 100ms delay. Can someone from Nordic definitively...
Hi community,
in our setup we use the LSM6DSL IMU using TWI. First we initialize the TWI peripheral, then we configure the IMU. After that we initialize PPI to automatically...
I am trying to build the project "thingysdkv210" which is downloaded from https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download#infotabs...
nRF52 DK
HTS example
I added app_timer_stop_all() in the ble_evt_handler() of main.c, under the case of BLE_GAP_EVT_DISCONNECTED, but the battery service timer still...
need help on multiple things
All work is on the DK 840 board using sdk15.3
Started with this link
https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic...
Is it possible to run the Zigbee Light Switch example with the internal RC.?
On the sdk_config.h I have changed the following:
#define NRFX_CLOCK_CONFIG_LF_SRC 0
But...
In the only example in SDK16.0.0 with soft_device and Free RTOS, configMAX_PRIORITIES is set to 3, which means available priorities 0,1 and 2.
Is it possible to change configMAX_PRIORITIES...
