I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hello everyone,
I've been messing around with a nrf52840 dongle we've got in our company and I wanted to restore it to the original state, but I cannot find the hex file...
Hello,
I've uploaded the Asset tracker example via SES version 4.20a. Uploading works just fine but when I open LTE link monitor, I see that the board constant reboots....
Hello,
in my application I want to power the nRF52840 with USB at the VBUS pin or a 3.3V external supply at the VDD pin.
I wonder what will happen if someone plugs in...
Hi,
My problem is that reader sends PPS command (both DRI & DSI set to 0) for which there is no response/confirmation from library, and I don't know how to implement this...
Goodmorning, I have a new Thingy 52 and I can"t get it connected to my phones. The old phone has Android 4.2.2 and the new one Android 10. On the I Phone it works perfect...
Hi
I am using Nordic softdevice S340 for developing a proximity search project. The softdevice function "sd_ant_prox_search_set (uint8_t ucChannel, uint8_t ucProxThreshold...
Hello,
i am currently trying to add my own model to the Mesh Android App. It should just be a simple sensor model.
It already works to have an own Window, where I can...
I want to store data on a specific location in Flash, so it is available later on in a bootloader. The size of this data can be quite large (~ 300 kB). I'm kind of puzzled...
Hi,
I've developping a firmware for the nRF52832 with the nRF52DK and it work on this board and on an external BLE module from EBYTE (E73).
I want to flash an other hardware...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
I'm currently developing a custom bootloader for DFU, using I2C.
The bootloader is based upon the secure UART bootloader for nRF52832. Transferring and writing the...
Hi Nordic Team,
In the recent Nordic APAC Event, we got nRF52840 Dongle and we would like to use it as BLE sniffer.
Can you please point out some resource/link which...
On the NRF52840 what is the max speed I can program the unit at. In the datasheet SWDCLK says it has a max of 8MHz. Is that supposed to be the max. I have two segger programmers...
I am using the nRF52DK board.
I use the " ble_app_template_pca10040_s132 " for testing.
I want to advertise 2 custom UUID (SERVICE_DATA " 0x16 " & SERVICE_DATA_128BIT...
