Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
My customer looking for very low power solution for their project. It's not reuired fast answer of node in network or permanent connection with each device. Just a rarely...
Is it possible to talk TCP/IP over BLE on nRF52810 (similar to PAN profile on BT classic)? Can SD S112 fullfill this or would S132 be needed. I know memory needs are an issue...
HI.
I use BLE in observer role. I register event handler only ones in initialization: NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);...
I am using the secure_bootloader to perform firmware updates via USB on the nRF52840 (custom board). This works great when I start with no application (only bootloader and...
Hello,
I am developing product on nrf52 with sd s112_nrf52810_5.1.0_softdevice. My application caused unexpected sd fault at adress 0x000089B2. I expect it to be something...
Hi Great Nordic Support Team:
Our client is going on the project with capsense touch sensor.
They're wondering about if there is any reference design about it.
Any...
Is it possible to use the timers in components/nrf_drivers/timer along with softdevice s132? If I enable the softdevice by calling softdevice_enable() my application restarts...
Hello,
My nrf51822QFAAH2 doesn't start, I mean that when i plug it, i can't see any Bluetooth device on my mobile detected, maybe I am missing a step, I don't know,
Here...
Hi.......
i am student , i am doing a project based on temperature. i want transfer data from temperature sensor to phone via using NRF connect . can you help me ? how to...
How send the larger data,which is more then 300 bytes in spi master example.i am using the Sdk 15.0.how to enable the spi .please send the default pins used for the spi.
Above is the "inverted—F" PCB antenna referenced.Below is the RF SCH and PCB layout,the PCB diameter is 20mm.Chip we use nrf51822 and bal-02d3.
Can the antenna work...
Playing with the logging and cli commands for logging, I normally get this if all my modules are lowercase named (but also if they are alfabetically after CLOCK):
It seems...
I have met a problem, that I can't download the previous version of nRF5 SDK, like 15.0.0, but only the lastest,15.2.0. Because a lot of work of mine is based on version 15...
I have successfully built and run the mesh examples 2.2.0, on several nrf52832dk boards with the exception of the EnOcean Switch example.
I can successfully build and launch...
