Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
We're using PWM on the nRF52811 to generate a 3.2 MHz clock needed by one of our peripherals, using the nrf_drv_pwm library in nRF5 SDK 17.1.0. We're seeing power consumption...
Hi.
I've been developing with nRF54L15DK.
I added below in prj.conf.
Indeed, I could confirm CMSIS-DSP function normally running in main.c.
In my goal, I would like...
Dear Sirs, This is about the software maturity levels of the nRF5340 Audio.
According to the page below, the Maturity level is set to ”Experimental” even in the latest SDK...
HI Teams
I referenced the Thingy91_X design. The MCU nRF5340 connects to the nRF9151 using two UART interfaces, but AT commands should only require one UART.
Under what...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
I print every 500ms. Here are the last few
timers:INFO:millis 510500, cnt 16728087
timers:INFO:millis 511000, cnt 16744474
timers:INFO:millis 511501, cnt 16760868
timers...
Hello,
I have measured the current consumption of the timer example of SDK13.0.0 with PCA10056.
With timer prescaler set at 16MHz i have 1.28 mA
With timer prescaler...
Hi, I got nRF52 DK PCA10040 device(s132) and follow the steps from devzone.nordicsemi.com/.../ to use arm-none-eabi-gcc(version 5.4) to build examples like blinky. I can successfully...
Hello,
I was wondering whether or not it's possible to achieve a data rate of 160Kbps using BLE4.2. According to what I have read on this nordic blog it should be feasable...
Hello!
I hope this question has not been asked before - at least I can't find it.
I do have an application with two vender specific services (128bit UUID's) and I want...
Hi,
i am doing ble_app_beacon code on nrf 52832 with sdk 11 and s132. the packet, its advertising should only be received by the device whose bluetooth address we are providing...
main.c ble_uart.hex
Hello,
I use nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice configuration to test the ble_uart program.
i use nrfgo Studio to load the...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
Hi guys,
I want to know whether the provisioning beacon can relay by the relay node or not?
If not, when the unprovisioned device's radio is not in the range of the...
Hi Sir,
I'm studying the nRF52840-PDK, and i found there are two debug connector. One is Debug in connector (P18) and another is Trace connector (P25).
As check the...
Hi!
I am fully aware on how Eddystone works. Or at least I believe so. Sadly there is some weirdnesses when I am trying to broadcast using the Nordic SDK.
So what am...
