Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi, I'm wondering how much i need the LF crystal oscillator.
In this case, the chip is never asleep, in constant latency mode, and is constantly advertising and meshing...
Hey guys,
We have several different devices that use the nRF51822 and some using the nRF24L01. We currently use the proprietary RF protocol and have all of our devices successfully...
Hi,
Reading from flash, an already programmed key, returns zero.
Using sdk 12.1, sd s132_nrf52_3.0.0, nrf52832, and pstorage. The key is programmed after uploading the...
On nRF52 interrupts for GPIOTE, I need to perform one event when a button is pushed, and perform another different event when the button is released.
I've checked these...
When the PPK calibrates and turns off the DUT, does the nRF52832 on the PPK disconnect from the External DUT lines? My DUT has a LOT of capacitance on it, and it takes several...
Hello i use the example ble_app_beacon_s130_pca10028, i'll try to add UART functions, but they not work anybody has this problem, please help me!!
int main(void)
{
uint32_t...
Hi..! Friends..!
I am trying to detect the number of steps on accelerometer.
For which I want to Plot the accelerometer values in real time (with minimum rate 50values/sec...
I would like write music box by buzzer. So I need adjust the PWM frequency continuously.
But i don't find the sample cede which is about adjust PWM frequency in SDK.
Where...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi all, present I'm working on sdk11.0.0 now I need to move all my projects to sdk12.1.0 . And all my custom projects have dfu support. In sdk11.0.0. when I select board for...
hello ,
i am trying to make communication between two (stm8s+nrf24l01) modules for which i am using this link zewaren.net/.../110 ,
by this code i am able to transmit data...
hello,
i am using ble_uart_app project in that i have added the pwm feature and added my code. i have tested my code seperately it works fine but when i have added in the...
Hello,
I'm realizing dfu.
1st case - for test
NRF_LOG_PRINTF("main start\r\n");
// ******* main loop start ******* //
while (1)
{
enterBootloader();
}...
I'm trying to set a global variable in RAM as uninitialised so it can be read back after a soft reset condition:
uint32_t data __attribute__((section("NoInit"), zero_init...
