Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello,
I want to allow users to change the device name as they like. I've been reading about it and I know what needs to be done, i.e. write to the device name characteristic...
i want to add a PA for a nrf51822 chip inorder to extend the coverage. i choosed a PA IC named RFX2401C.i am wondering how to deal with the TX pin and RX pin of RFX2401C.could...
Hello Guys,
I use BMD-350 rigado module for development. Now I want to programme it using raspberry pi 3.
I am using OpenOCD in raspberry pi to programme nrf52 chip...
hello,ereryone!One nrf52832 as ble_central,and another nrf52832 as ble_peripheral.
and the ble_peripheral (nrf52832 )set static passkey:
#define SEC_PARAM_BOND 1
#define...
I am working through the heart rate monitor central ble device code on Nordic SDK 8.1. I noticed that the variable
bool m_memory_access_in_progress = false; /**< Flag to...
I'm wondering whether or not we can make a specific BLE peripheral device with having this ability to be supported by client iOS/Android device for automatic scanning/reconnecting...
Hello everyone,
Recently I've had problems with using JLinkExe directly from the Linux terminal. I finally decided to give nrfjprog a try. It worked, I can finally type...
I develop a nrf_mesh application.
I can send a mesh packet by nrf_mesh_packet_send().
But I can not receive a mesh packet.
(I can receive a advertise packet by nrf_mesh_rx_cb_set...
I am developing an app that uses both a central and a peripheral device using Nordic SDK 8.1. I was working off the hrm example code and wanted to move all the scanning methods...
Hello all. I am a beginner with nRF and am trying to get the Eddystone example (titled "experimental_ble_app_eddystone" in the examples folder) to work. I have opened the...
Hi,
I am working with the BLE Nano module and the mbed online compiler. I have the Nano acting as an SPI slave. The problem occurs when I try to add BLE functionality....
I've spent some time searching and haven't found a definitive answer or anything obvious in the code. I'm developing the firmware for my application on the nRF52 DK, which...
Hello nordicers,
I'm stucked with long writes (android central to nrf52 peripheral)
I'm using SDK 12.3 and S132 v300. Android as the client central (RxAndroidBle libary...
