Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hi,
I have problem with long write by sd_ble_gattc_write.
I send first 18 bytes by button on pca10028, then I waiting for BLE_GATTC_EVT_WRITE_RSP and sending rest of bytes...
I need some help with something very basic...
I need a way to upgrade my DFU BLE bootloader to either reset back to the app if no update has been sent after some timeout...
hello,
According to the "twi_scanner" example from the SDK12.2 I don't understand how the respective I2C pins/GPIOs are set up.
There is this function that I found "nrf_gpio_cfg...
My nRF52 device is an asset tracker and does not have a comm port. I have been looking at a BLE dongle setup for manufacturing test but the results are not repeatable with...
HI,
Nordic part used is nRF51822.
Is there any way to increase signal strength of BLE tx?
I see some parameters in advertising_init function for advdata.p_tx_power_level...
Hi all
According to chapter 50.2 of the nRF52832 product specification V1.2, the pins used for the UART peripheral should be configured before in the GPIO peripheral to...
why most of the examples of sdk 12's sdk config file has different options?
I'm trying to build an application that has Central and Peripheral Role application (and it...
Hi,
I have noticed the new preview DK for NRF82840 is now available, and the new chip is running the new BLE5 spec. My understanding on the BLE v5 is the higher data rate...
Dear Team,
We are facing an issue in nrf51822. We are compiling same project on different system in log file we got certain differences such as
System Licence
...
How to change Peripheral Role to Central Role without having concurrent Role?
I know S130 Can have 8 Concurrent Role as Central, Peripheral, Observer, Broadcaster.
But...
Hellow i am starting with nrf51, and reading nAN-36_v1.1x.pdf doucument
about using use a button to sent a signal through ble.
the BLE hellow world.
but I cant find the...
I'm trying to program 500 raw (not populated on boards) Taiyo Yuden EYSGJNZWY modules, which uses the nRF51882 chipset.
Does anybody know where I can get a fixture to do...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
Long story short, I need to create a packed struct.
I knew the pragma way, to change aligment, didn't work.
I looked up and found the __packed (I'm using Keil µVision...
