Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
Hi,
I'm using the Ellisys tool to capture packets and compare the differences between CIS and BIS. The capture results for BIS show that it is unencrypted, as seen in Figure...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
I followed the steps here docs.nordicsemi.com/.../building.html: PS C:\ncs\v2.9.1\nrf\applications\nrf5340_audio\tools\buildprog> python buildprog.py -c app -b debug -d gateway...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
Dear Nordic Team,
I hope this message finds you well.
We are currently working on a project that requires generating continuous traffic using Classic Bluetooth, and if...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
I have a strange behavior with the Timers. For my project I use a Raytac module with a nRF52 Chip on it. Softdevice is not flashed. Project is based on SDK 11.0
When I...
My setup:
NRF52DK;
Keil 5.22.0.0;
nRF5_SDK_12.2.0;
S132 3.1.0
While trying to use ble_peripheral\ble_app_template\pca10040\s132\arm5_no_packs I decided to modify...
I'm sorry. I closed this question and can't reopen. I need more answer.
If I solve all problem I'll close this question.
As you mentioned I'll try HW version modification...
I've just noticed that it's possible to call ble_advertising_init() and ble_advertising_start() with params that are quite conflicting.
ble_adv_modes_config_t advertising_modes_config...
Hi dear Engineers!
We want to add Eddystone compatibility to the device.
Is it possible use nRF52 silicon radio ?
How I understand, it is not compatible with any SDxxx...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
