Hello everyone
our current project is to use dht22 to control an external fan
but we don't know how to add a new node to the device tree for the fan.
The picture below...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway in bis-headset at the same time. Can...
I got the license key for segger studio but the option to install the license is not popping up. https://drive.google.com/file/d/1qok8PcCYhHi_9nsknL2JW4_AtF6F5ZP5/view?usp...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
I've got a project based on NCS v2.6.0 using a nRF52840 as contained in a Fanstel BT840F module.
With help from you all (thank you!), the software works. Bluetooth and PWM...
Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
Hi,
I'm doing nrf52833's spi function.I want to use hardware slice selection instead of pulling the gpio pin, and the reference manual has the register IFTIMING.CSNDUR....
Our custom development board uses an nrf52840 chip together with attached sensors. The data from sensors are stored in sd card. For this purpose, the Zephyr fs library is...
Here is a stacktrace from a device I got using the nRF Connect mobile app on Android.
nRF Connect, 2024-05-11 Device Name (A4:XX:XX:XX:XX:7C) D 13:40:23.035 [Callback] Connection...
I'm trying to setup a I2S module by referring the I2S module given in the nrf5340-audio application. This is my audio_i2s.c file.
Now when I'm building this...
What should I change to run the hci_lpuart sample with UART asynchronous API instead of the using the interrupt driven one? I have already changed the source file on the sample...
I was able to run blinky successfully on my customized nrf5340 board, but it doesn't respond to writing matter related code, there is no output from the RTT, I refer to the...
Hello,
I am reaching out regarding some challenges I've encountered with SPI communication on the nRF7002DK when interfacing with the ETH Wiz Click | Mikroe module and a...
Hello,
I am a student and new programmer and got the Thingy:91 for a project at Uni. I went through the getting Started guides and now I am at the point, where I downloaded...
I tried adapting the blinky sample project to work with a custom board. After an hour or two I was able to define the GPIOs of my schematic including I2C with the device tree...
Hello,
we are trying to implement a custom Friend node research policy, before the friendship is established.
Since bt_mesh_lpn_poll() works only when the frienship is...
Hello,
is there any example using the IEEE 802.15.4 driver?
I was able to send and receive a some packets by using nrf_802154_receive and nrf_802154_transmit_raw, and...
I'm using an nfr52840 board.
I noticed that when using The 'zephry-sdk' v3.5.99-ncs1-1, when doing a passive scan using:
BT_LE_SCAN_ PASSIVE
which sets:
BT_LE_SCAN_PARAM...
HI , currently i am using nrf52840 soft device s140 sdk ver. 17.1.0 i have two controllers i need to transfer the dfu ota file form one controller to other controller using...