Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi Nordic team,
We're experiencing two issues related to partition handling in Zephyr/NCS and are looking for your guidance
Issue 1: settings_storage is erased after BLE...
spim2、ncs2.6.1
I used SPIM2 to send the string "Hello, SPIM!" and receive data of the same length.
However, on the logic analyzer, I can only see the transmitted signals...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Hello all
If you could please point me some directions on how to solve my issue, I would be grateful:
Some background info:
SDK used: 9.0
spi master code =...
Dear Nordic Developer Zone,
I have a silly question. After searching in the Nordic and Bluetooth documentation, I didn't find what CCCD and SCCD mean. Theses metadata are...
I had a design on 4-layer PCB with nrf51822, then the requirement was changed, then the 2-layer is sufficient for routing.
But I thought 4-layer PCB is better for RF circuit...
I've run into a problem with an OS API call when running FreeRTOS on an NRF51 due to how ticks are corrected.
vTaskStepTick() is getting called while the MCU is awake and...
Hello all,
I am trying to activate ADC to measure a voltage every few seconds using nrf51822. When it is done, I supposedly deactivate ADC so it does not consumes while...
I am designing an device and i need to communicate with the device using the I2C of my nrf52.
when ever i try to initiate the transfer process using the driver function...
Is there a Peripheral Encryption Example for the nRF52? and can the Master Control Panel tool(3.10.0.14) be used to test the Peripheral Encryption?
If i clcik the down arrow...
Question about usage. I am using the nRF52, and ported product code that was running on the Alpha SDK11 to the release SDK11. I believe that what I will describe is a new...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
