Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
I have been trying to pair my nRF51822 heart rate monitor device with my Windows 8 laptop. Every time it is unsuccessful and returns the message try add your device again...
Hi
Doing some testing of the nRF24L01+ with LNA PA module, i have noticed noise on the 1.2 GHz frequency, this noise seems to be larger than what is allowed if i was doing...
HI,ALL
with ' nRF51_Series_Reference_manual v3.0.pdf ' , i want to know which pins can i used for adc purpose.
in the sample code.
void adc_config(void)
{
...
Hi there,
The s132 v2.0.0 production softdevice was released recently. How can I use it with the nRF5_SDK_11.0.0-2.alpha? or I have to wait for a new SDK release? When...
I have a bluetooth service which I want to have to initialise a TWI transaction (using app_twi). I want to get the data back from the TWI transaction, but I can't figure quite...
What is the pitch and spacing of the connectors on the underside of the PCA10004 and PCA10005 modules please? Is there a diagram showing dimensions anywhere in the documentation...
@Michael Dietz
Hi Michael!
I am not sure what happened to my last question regarding the BLE example using Segger Embedded Studio. It is no longer visible in the post...
i am already use sdk10 and Eclipse gcc tool chain set-up.. but when i am programming on nrf51822. so, it's not work. also, it's working on nrf51422 QFACAB0(0x0071)..
GIVE...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have the ble_app_hrs example working well with DFU.
When I take main.c from the example code and put it into an RTX project, the DFU stops working.
Symptom: nrfToolbox...
Hi,
I have a python scipt that uses pynrfjprog to program some custom information into a board's flash to be used by my application (calibration parameters, serial number...
I managed to compile the ble_app_uart on windows 8.1 with cygwin. I had to remove all abspath on the makefile, as launchpad gcc is not compatible with cygdrive notation.
...
Hi, I use the NUS most of the time.
(SDK 7.2 & S110 7.1 with IAR 7.1)
As you know, HID keyboard or mouse bond with centrals (smart phones).
After bonding, when using...
nRFgo was unable to read attach to the boards I have with the QFAABB parts, but reported QFAABA parts correctly and programmed them. nRFgo was at 1.21.02.
I updated to...
Hi,
I'd like to retain a value in RAM after any type of reset, including a watchdog timeout, so that I can read it back in the bootloader immediately after a reset.
...
