NPM2100 EK CONNECTION
Can I connect The NPM2100 EK with NRF52 DK? If so..... 1. How do I physically do this? 2. Can I program the NPM2100 EK to send Voltage Supply of 1...
I'm trying to convert some code from ESP32 to nRF, and I'm having problems with the microphone input. Mind you, I'm a beginner with nRF, so I'm sure I'm missing something...
Hi,
I got my hardware modification which added the nRF21540 to our system more or less running under NCS v2.9.0.
Currently, I have the following FEM and antenna configuration...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Hi all,
I've build a custom bord with an nRF9151, I try to connect to aws iot but it's seems it's doesn't work probably cause by bad cert, I got AWS_IOT_EVT_DISCONNECTED...
Hello, We're developing a firmware for our board based on nRF9160, using ncs 2.7.0. We want to allow the user to set the certificates over i2c. How can we in a secure mode...
We are developing an IoT device that utilizes the nRF9151. We would like a review in the second round of our schematic and layout to understand if there is any issue that...
Our present application makes heavy use of the nrf51822 UART and I2C interfaces. We have a 115200 baud UART channel and thus need HW flow control. We are interfacing to an...
I would like to create wearable fitness based applications/hardware using nRF51822. But i am not sure how to get the fullest of power down modes in the chip.
For example...
Hi,
I purchased an nRF51 DK recently.Followed this tutorial to compile and flash an example project:
devzone.nordicsemi.com/.../
Here are the tools used:
Keil...
Hello，greetings.
I am trying to communicate among 2 NRF24L01+ modules using stm32 and stc89c52.
With EN_AA = 0x00, EN_RXADDR = 0x00, SETUP_RETR = 0x00 on PTX ,and EN_AA...
Hello,
I want to use preprogrammed Long Term Key (hard coded) with Device Manager for nRF52. I found the dm_enc_key structure but I could not find any solution to provide...
Hello all
I have an nRF peripheral based on S130 SD. I have exposed certain services with both read and write permissions. However i would like to secure these services...
Hello,
I have developed a simple characteristic to send data over ble using the ble_nus service.
I created a service and added a characteristic to send. Then sending the...
I am working on a BLE device (currently being prototyped with the mbed DK). It connects to a smart phone app. I would like to build in some security features, definitely some...
Hi guys I just bought:
one nRF51 Dongle (nRF6825 Rev 1.1.0 2015.27)
some nRF51822 Bluetooth Smart Beacon Kits (nRF6930 Rev. 1.0.0 2014.27) that are basically beacons...
In my application I need to use the whole flash memory available (128 KB of the nRF51422 QFAC). My data is first stored on a 2KB buffer and once the buffer is full, data is...
I'm trying to figure out why I need to rebond after completing a DFU upgrade with Android 5.1.
My bootloader does not modify the device manager pstorage state, but I am...
Hi!
I've just started developing with NRF51422 (PCA10028 board). I downloaded the free version of Keil MDK-ARM and loaded the "ble_app_uart_s110_pca10028" example from...
Hi,
We wanted to create a device what control with a remote controller but we want to controll this device by smartphone also.
We going to use 51822 but it is not exactly...
Hello.
Our company develop BLE device and make some applications(android/iOS) for updating ble devices.
Those applications use nordic DFU source for installing firmware...
Hi
I want to configure SAADC channel to work in oversampling mode, and to enable burst mode.
nRF52832 Objective Product Specification v0.6.2 says:
"CH[n].CONFIG.BURST...
