Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
In IAR Embedded Workbench for ARM, version 7.40.3.8938 (w/ common components version 7.2.4.3784 ) with nRF5x MDK for IAR version 8.0.3 .
When selecting the target in General...
Hi,
I have a couple of nRF Beacons and want to change the program so that it scans for iBeacon packets before starting to advertise.
The flashed program is just advertising...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
hi everyone.
we are migrating to nordic nrf51 series (before we used ble modules from another vendor blugiga which depends on cc2541 chip) so I m pretty new at nordic nrf51...
Hi all,
I'm using the pca10031 which contains the nRF51422 chip; as a packet sniffer to sniff the communication between my S5 samsung and my pca10028, but I struggle while...
Hi, I'm trying to use the example bootloader with the new NRF52, everything seems to work fine except that I'm unable to bond to the device when the bootloader is installed...
I sniffer the packets when I use a phone to connect to a BLE device.
However, in the packet with CONNECT_REQ label, the source address (init address) is not the bluetooth...
Hi.
I'm trying to communicate with legacy nRF24L01P using nrf51822.
I received packet from nrf24l01p, but I can't send information back.
The data I should send is more...
I use the persistent storage manager for saving some calibration parameters. It seems to work ok - I can power off/on, and the values are still there.
However, after I...
Hi. I would like to get into bare metal programming, and have decided to go for ARM processors. Are there any ns-kits or courses availible for purchase?
thnx in advance...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
Dear All,
I'm trying to set a static passkey. I have created 2 custom characterestic. One characterestic is used for notifications and the other one for writing. For communication...
