Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi Team,
Can anyone help me on this?
How to decrypt AES-ECB-Nopadding Encrypted frame?
I am not getting desired output. In fact, I am not getting how to proceed in...
I am trying to get buttonless DFU via BLE to work with gcc compiled apps, but it only works on the first DFU attempt. Every repeated attempt after that is timed out after...
(I use nrf51822)
I use two 3V batteries in series.
Therefore Input Voltage of My Circuit is 6V.
My own source was coded as a collection of information.
Oh, by...
Hi,
i would like to know how can i enable the single-cycle 32 bit multiplier buit-in on the M0 Core.
Checking the assembly code every multiplication calls to __aeabi_dmul...
Hi,
What is the minimum time needed between two capture tasks for the same CC register?
I would like to timestamp the Address and End event of a packet in the same TIMER0...
Hi,
I am thinking of moving advertisement and scanning function execution to RAM to reduce the energy consumption since nRF device advertise in each 1 second interval(frequently...
Hi ,
According to nRF51822 Product Specification, running code from flash draws about 4.1mA and running it from RAM draws 2.4mA. But when I tested my code it draws more...
I think the time of uartput is too long (beacuse of the packet recived is too long ,but i can not change it),and when the BLE_GATTC_EVT_HVX comeing ,the uartput is not over...
Hello all,
when using the android version of nRF Toolbox app i am unable to perform a successfull dfu when the application firmware file size is greater than about 60KB...
(mp3 or wav file) --> sd_card --> nrf51822 --> smart phone
Read the data from the SD_CARD transfers to smartphone.
void BLE_SEND_VOICE(void)
{
f_mount(0,&fs);
...
I've not worked with BT4.0/4.1 before, so I was wondering about this:
Take the heart rate monitor example, connection happens automatically when a heart rate monitor is discovered...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
I'm interested in using the chip and a very simple board. No buttons, no humidity or motion sensors, just the beacon (like a heartbeat). I'm trying to keep the price down...
Hi all,
I am using the experimental_ble_app_multiactivity_beacon example with S110 v7.1 and SDK 7.2. In particular the hrs_scanner app on the pca10028 board.
I am using...