Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hello,
I am currently designing a project that will advertise as two different beacons simultaneously using the Timeslot API. I have successfully implemented the nRF51...
In my all projects, I am using this code to obtain and set local device address:
uint64_t deviceId = ((uint64_t)NRF_FICR->DEVICEID[1] << 32) | ((uint64_t)NRF_FICR->DEVICEID...
Hello,
I build a Broadcaster(iBeacon) with the DK PCA10028. This Broadcaster sends periodically ervery 30ms a message (I have sniffed the Broadcast message and it appears...
Hello,
I am having some strange results with some firmware I have been developing. I developed the firmware on the nRF51 Development Kit (PCA 10028) and the device advertises...
hi,
i would want to develop a project with master (mobile phone)- bridge (acting as master and slave,nrf board)- slave (nrf board) .
i have tried the ble central(s120...
I use the Android 5.0.1 lollipop, SoftDevice S110 6.2.1 and SDK 5.2.
When a Bluetooth scan performed on Android phones,
0x10 (Connect), the event occurs and after 0x12 ...
Hi
I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac OSX. I use the NRF51DK as hardware, but also had it working using...
Hi
I'd like to realize below function for our product.
The product has static passkey in factory.
A user who use the product will pair with his smartphone using...
Hi, I am soon going to run initial RF Performance Tests. We have designed the board IAW Nordic recommendations, so I do not have any special test points and/or RF connectors...
Hey I am a beginner and I want to use mpu-6050 interrupts to sample the sensor values. I am able to read and write values through i2c but I want to read values only when any...
Hi, I'm updating my code which used to have a direct handler GPIOTE_IRQHandler(void), however I can't seem to get this working.
The Kiel Run Time Management has a requirement...
I updated from SDK 8.0 to SDK 8.1. My project had both app_uart and app_gpiote. With 8.1 (I don't exactly remember how it was on 8.0 and I have not spent any time researching...
I wanna use a nrf51822 dongle to sniff all data packets sent by 4 to 6 beacons, without large loss. The code I use is a python api given here learn.adafruit.com/.../python...
