Hi ,
I want to use nRF connect sdk for visual studio for windows os.
I installed the required tool chains 1.nrf-command-line-tools-10.24.2-x64 2.JLink_Windows_V832_x86_64...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
Hello,
We are currently in the process of developing a custom board containing the nrf5340, which will act as a central for HR devices and a peripheral for data transfers...
Hello,
I've received a strange error when attempting to send the %BANDLOCK, any idea what it could mean? I don't believe 65536 maps to any of the error codes here , but...
Dear Nordic Engineers
The following documents are our hardware designs. When we conducted the test, we found that we couldn't obtain the GPS satellite signal and the 4G...
Hi,
I was talking to Susheel Nuguru about the multiconnection problem that i had in my other ticket about multiconnections for Channel Sounding, which had the same title...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
I am using the nRF51822 and code base 6.1
How can I program the advertising mode of the beacon to not time out. I am looking to advertise for 10 seconds and then go to sleep...
When I downlaod and program the softdevice version 6.2.1 via nRFgo Studio, it shows Softdevice version as S110_nRF51822_7.0.1 after programming.
Any idea why actual version...
i use nrf51822 for my project, i want to do is when smartphone are pair with my module i store one flage in flash whenever user enter right security key and after reset i...
Hello,
I have purchased NRF51 MBED enabled board. I need some assistance in how to get started. I want to use the KEIL software and I am not able to.
I have downloaded...
I need a reference design of nRF51822 for minimum 1 meter range . The circuit will run from CR2032 battery for at least 24 hours and will take some readings from ADC input...
i am unable to sniff the packets between two devices once the connection is established between two devices..i am using nRF sniffer 1.0 ...
i am able to see only the advertisement...
Hi,
How can I control the PDU error code when reading an attribute.
E.g. Attribbute not found 0x0A. For more info see 3.4.1 Error Handling Bluetooth spec 4.1 Volume 3...
Hi,
I have created a custom PCB that more or less follows the Nordic SmartBeacon design: Beacon_V2.pdf
Instead of BAL-NRF01D3 I used the BALF-NRF01D3 as this is supposed...
I have use random number generator in S110, the source code just like:
uint8_t num_rand_bytes_available;
err_code = sd_rand_application_bytes_available_get(&num_rand_bytes_available...
what does it mean the VTG led turn red ? but it has no bad effect to my project. In addition, I find a strange phenomenon. I use three 1.5v battery to power my board. The...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi nordics!
First of all, thanks for answering my questions before.
Now, I want to generate a clock(48 pulses) with 200us width.
However, sometimes the width of...
Hi ,
I have a application program which uses s110 and UART service .
The issue is the program is not working when I enable the Micro Lib in keil.
On observing the map file...
Hello,
I want to use flash for logging sensor data and sending via BLE.
I found several APIs for store data to flash.
pstorage (Persistent Storage Access Routines...