Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
I am trying to create a partition on my external flash using littlefs
Here is the line that is returning me an error
FS_LITTLEFS_DECLARE_DEFAULT_CONFIG ( storage ...
I've done a lot of reading on the forums about this topic and done a lot of trying myself. I haven't had much luck and it seems like most everyone is in the same boat.
...
Hi,
On my ble application, I want to keep after wake up reset the previous value of a variable, I tried using sd_power_ramon_set(0x000f000f) to keep on all ram partitions...
It seems like a pretty large hardware/software release just came out and I am a little confused. Where can we find documentation about all the new hardware (nrf51822-QFAX...
Hi I try to run master control panel on PCA10024 development boad. On master control panel, I set File->Options->Serial port: "Show all serial ports". Then master control...
Hello,
I'm reading S210_SoftDevice_Specification_v2.0.pdf and there is written: "The ANT channel encryption engine provides the ability for a single channel..." does this...
I didn't find information about size of buffer within softdevice 310 for ANT messages.
I found that S310 requires: 128kB Flash, 9kB RAM, Stack 2kB
But how big size of...
Hi, are my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS or AIN_2_3_PS will not...
Hello,
I'm currently seeking for parameters that could improve our ANT communication stability. I read, that there are possibly override parameters in the FIRC that have...
Hi all,
I try to reduce the power consumption of my GZLL host (RFDduino/nRF51822).
I use the Arduino IDE to program my RFDuino.
My Idea was to synchronize the host and...
Trying to flash a program with Keil. Worked fine with SDK 5.2, now with SDK 6.0 get the error: Insufficient RAM for Flash Algorithms.
My options for RAM:
Start: 0x20002000...
Hi, Nordic
I added "//" to the srccode of main.c in project ble_app_hrs just like below
bond_manager_init();
// ble_stack_init();
ble_error_log_init();
timers_init...
L.S.
Suppose I want to customize the transmit power at installation time, not at build time or production time, how would I go about it?
I have adapted the proximity...
Hello,
I want to use DFU with single mode mode.
I included in build dfu_single_bank.c instead of dfu_dual_bank.c.
But after that DFU device begin to work with errors...
hello,
I am working with S130 demo app. But I could not find any registering of event handler being done usind softdevice_ble_evt_handler_set(). In both S110 and S120 demo...
With the maximum SPI speed of 8 Mbps, I was expecting to be able to send 2 bytes in just a little over 2 us, but it takes a lot longer. It appears that the mandatory event...
