Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi Team,
I want to develop an application based on Mesh5.0, but I also want to use functions that in nRF SDK. I find the sd_app_evt_wait() in the main function. But in NRF...
Hi,
I have setup a provisioner using the provisioner example of the mesh sdk.
I have also setup 10 nodes using the on_off example of the mesh sdk.
I have provision...
Hi all,
I have successfully followed this [tutorial]( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
Hi!
I am trying to flash a component on my custom embedded PCB that embarks a NRF52832 through BLE. To do this, I run on my PC a python script that reads from a hex file...
How to enable Read back protection in nrf52832 and in nrf52840 after DFU completed.
i have tried using --rbp all its working but i want to do in code(any register or by...
Hi, I'm using the PCA10056 with NRF52840 and I'm using the P24 Section, there's a pin that doesn't have number and neither is connected to GND...
(the pin in the right down...
Good day!
I've found that with connected proxy and enabled filter node only forwards messages and doesn't use advertising. I didn't found in Mesh Profile v1.0.1 any mention...
I'm using a nRF9160-DK (PCA10090) but I can't see connected device on Programmer (v2.0.0) nor LTE Link Monitor (v2.0.0), both installed and launched through nRF Connect for...
I recently installed the nRF Connect extension for VS Code on my PC(Windows 11, 10700k).
I cannot see my connected boards.
But the "programmer" of the nRF Connect...
I have tried a lot but my DK wont enter in Bootloader mode, or atleast the Bootloader folder does not show up in my Windows 7 machine. I am able to do that comfortably with...
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2 is pulsing red...
On IN141 Informational Notice v1.1 changes for nRF52840 to revision 3 (build code Fx0) are presented.
One of the changes is "New (optional) filter coefficients for pulse...
Hi all,
I am currently developing audio sampling on a custom board using the nrf52832. I'd like to sample at 20khz and am using the nrfxlib driver for this ( https://github...
Hi everone!
I am developing with SDK17.0.2 and using the nordic NUS peripheral example.
I am seeing a strange effect:
I am connecting from an android mobile and when...
