The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello,
I have the following setup where I am trying to access a function in nrfx_spim.c (red box) from the file mm101_drive.c (green box).
However this function is...
Hi, We have a device configured as a peripheral and want to provide the user with the peer device name typically connected to it, like the device name. Typically a phone will...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands(READ, WRITE, etc.) to the IntanRHD2132(ADC) at regular...
We have a sudden problem with the flash_manager. The code stops at static uint32_t flash_area_build(flash_manager_t * p_manager), at line NRF_MESH_ASSERT(p_manager->config...
Hi.
I am designing a 4 layer PCB (0.8mm thick) for an nRF52820 microcontroller.
My board's stack: L1 - Signal L2 - GND L3 - Power L4 - Signal
I have questions regarding...
Hi dear forumers,
I'm in the goal of achieving lowest current consumption on my PCA10056 DK board, with an nrf52840.
I converted a previous zephyr firmware who perfectly...
Hello, I am using the nRF5340 Audio DK with Zephyr and want to use I2S to send audio to an I2S device. So far I have had little success with the microcontroller halting in...
11 months ago in an answer a nordic member wrote (in regards to an error that I now also had and could solve using CONFIG_DEBUG=y):
[quote userid="81283" url="~/f/nordic...
Hi there,
I have an issue when using PPKII software on MacOS at 100ksps (no issue at 1K):
The 10min button at the top does not appear anymore
After a 3min measurement...
Good Afternoon,
I'm designing a 4-layer PCB based on an NRF52832 (QFAA) paired wit h a Molex 479480001 SMT Antenna, and I was hoping for some feedback on Antenna Matching...
Hello,
I'm trying to sniff packets with wireshark by varying the connection interval and supervision timeout of my ble application. I see that with lower connection intervals...
I'm presenting an issue when exporting the data collected, specifically the digital outputs, they are exporting incorrectly, but in the Data Logger tab they are presented...
When implementing AWS_IOT provisioning by claim process, AWS_IOT responds to the published topic $aws/certificates/create/json with a 3580 byte response. This causes TLS to...
Hey, I'm pretty new to Nordic Development. I am working on nRF5340 Audio DK development board right now and I was trying to create a bluetooth speaker kinda setup using the...
