Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello everyone.
I'm developing a custom board mounting the nRF5340, and I want to use the micro USB. I was looking at the schematic of the DK for reference, and I found...
Hi,
Not sure if this is the correct place to ask...
My code is crashing after a spi write function.
It is probally obvious to someone here, i think i fell into that...
I'm attempting to merge 3 HEX files into one using the Merghex command. The "BinaryImage access" error appears, see the screenshot below.
I've tried this several times with...
Hi,
I'm porting my SSD1333 (Solomon IC for OLED displays) code driver to Zephyr OS drivers for ease of use along with LVGL (going from `< nrfx_spim.h>` to `<drivers/spi...
I want to transfer a bunch of data over the virtual com port to a PC using the USB port on the nrf5340. I'm using the CDC ACM sample: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
why
AT%XRFTEST=1,1,14,7880,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7930,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7980,23,1,4,0,0,0,0,0,0
returns ERROR but e.g.
AT%XRFTEST...
We are trying to see if it is possible to detect a vibration using the ADXL362 accelerometer on the Thing:91. We have it setup to to trigger on motion, but we need to be able...
Dear all
I following the example here , over the air one, and get it basically working, thanks for the tutorial.
Now I have a few questions:
1. It looks like it always...
Hi
I am studying Matter, my setup is
chip-tool : chip-tool-android_armv7l.apk v2.1.0
OTBR : raspberry pi 3b + RCP( PCA10059 )
board : nRF52840-DK(PCA10056)
sample...
My pairing is working and shown as bonded on Android, but when the DK is reset, the bond is no longer valid.
In studying saving of bond information, I find references to...
Hi,
I am learning Matter. I have some questions:
Where can I get the resources, especially official resources, to study Matter?
What is the use of the Service discovery...
Hi,
We are developing our product using nrf5340. Currently, we are using NCS v1.9.1 for development. We need to give UART to test our Board for Certain conditions by using...
I have been learning to use the nrf52840DK for some time now, though I would consider myself still a beginner. Anyway, something has gone wrong with the kit and I am not sure...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
