The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello,
In my project, I have a device (nrf52833 custom board) which I want to operate in dual role (central/peripheral). I've followed a ble_app_hrs_rscs_relay example...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
How can I adjust the BLE transmit (Tx) power, up to and including +8 dBm? I'm using nRF Connect SDK (NCS) on an nRF52840-DK .
I modified the throughput sample to reverse...
Hello, I'm trying to run the Ble Peripheral sample from "nrf\samples\bluetooth\peripheral_lbs" i'm using nrf connect V1.8.0 and NRF5340dk i followed the code in the github...
Hi,
I'am using the Ultrasonic Oxygen Senor with the nrf5340, the output is like this "photo" I want to calculate the concentration and the purity and with this values I...
Hello,
Is there any way to program the frequency output when sending a carrier wave to have a step size of around 1KHz? It seems that the default step is 1MHz.
Hi
I am trying to get the manufacturer data by ble_advdata_parse() as instructed in this case and this case , but it's not found in my SDK14.2, so how can I get the manufacture...
It's not possible to proceed a firmware update of matter light switch example on nRF5340DK.
I use following SDKs / Repos
nrfConnect SDK v2.0.2
standalone zephyr SDK...
Hello,
I have a component (AMC1306) in which I input a signal of at least 5Mhz. When this signal is triggered to this component, it sends me back data at this same speed...
Hi, I am trying with coap_client/server example programs on a custom board. I created a custom board for Zephyr and it is compiled without errors. I have a single button switch...
Module: nRF52832
Implemented pairing for ble_app_UART (NUS). However, I can connect with ble_app_uart_c, which does not have pairing implemented. Please tell me how to prevent...
