I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Dear Nordic Engineers,
When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware.
During the FW upgrade the device flashed...
I am trying to use the DTM example for nRF5340 DK (PCA10095). The example is located at "C:\v1.7.0\nrf\samples\bluetooth\direct_test_mode", but I am facing "NRF_RADIO_Type...
Hello there. I am wondering, if while connection establishment or any other communication event through NFC and BLE the system addresses to NVMC? (Maybe mac address or some...
Hello
I search a way to have a similar project as pc-ble-driver with NRF connect sdk
There is a peripherial with many sensor that send data over BLE and i want to command...
Dear all,
When the provisioner add appkey or bind appkey for the node's model, I want to be informed and run a callback function.
Can I set callback for config server...
Hello Nordic support,
I am using the zephyr\samples\subsys\usb\mass example with an SD card. SPIM4 work on 16MHz.When I check this example on a Windows 11 machine, I observe...
I need to capture the time between rising transition of a GPIO pin in order to integrate a Manchester decoder of an RFID reader chip. In my particular case, the reader chip...
Hi,
I'm working on a project using BLE via s140, everything works fine until I look more seriously at the current draw of the device.
Simply, my project starts a Scan...
Hi,
I was able to get the DFU system working by CONFIG_BOOTLOADER_MCUBOOT =y. I notice that the default mcuboot update methode is using the scratch partition. According...
Hi,
We use the SKY66112 FEM in front of nRF5340. The FEM is configured in the DTS file. On our ordinary firmware, the TX pin is set and reset automatically. I can see...
I am trying to build a new workspace for my project using VSCODE & nrf connect. I select create new application and fill out the config as seen in attached photo. The build...
Hi connection,
I am trying to build indoor position system, Find the location, Find the direction and Distances project. can you suggest it is possible in NRF5340DK ?
...
I noticed in the nRF extension in VS Code, there are the "pristine build" and "erase and flash to the board" options. I was curious when I should use these options instead...
