Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle using...
I try to using nrf_fstorage_write() to write data to fstorage and then waiting writting finish. But it hang at sd_app_evt_wait().
int _fstorageWrite(const uint32_t addr...
I try to integrate https://github.com/NordicPlayground/nrf5-calendar-example into Keil project. But the following error messages shown when accessing NRF_CLOCK.
error messages...
Hello.
I have a question about programming a dfu + softdevice + app code using j-link.
I programed like below for using wireless firmware update.
program softdevice...
Hi,
in my application I have setup the nRF52 to wake-up from deep sleep if a low value is detected on either of two GPIOs (4 and 5). What I'm trying to achieve, is to be...
Hello,
with my nrf52dk board i had made some tests to check the scan performance.
Using nrf Sniffer - with Wireshark
nrf Mesh - LightSwitch Client (Mesh SDK v4.2...
Hi,
Automatic installation from ToolChain Manager, no errors. Perform west update ,no errors. Check all the files ,no problem found.
Have reinstalled NCS for many times...
Hi,
Using MeshSDKv5 on custom nRF and nRF52DK
We are working on an LPN wireless PIR sensor so which sends a sensor status publish message on occupancy.
I have notiiced...
Hello,
I want to keep perform some task periodically .. probably using tick timer / rtc / application timerof every 5 ms, to perform some task, without keeping the thread...
Hi,
I am transferring 100 bytes of data via BLE-Mesh from a vendor client model, which I need to receive in my vendor server model.
I referred to nCS provided chat sample...
I am trying to implement an already made sample from Nordic for INA219 sensor. As always it didn't work initially and showed many errors even though it was a sample code but...
Hi. I wanted to test the power consumption of the NRF5340 when using the Bluetooth low power feature. Using the Energy Profile Kit seems convenient but I am not sure if the...
I'm using a sample from nRF connect SDK v1.91.1 for BLE peripheral. I'm trying to read one of the buttons on the development kit, but I'm not very sure how to use the button...
Hello everyone,
I'm trying to play with PPK II to check current using ble_app_uart example (nRF5_SDK_15.0.0). I notice that the nRF52 DEV KIT keeps advertising and if there...
