Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi everyone. Here is my code for 2 different timers that put uc to sleep and wake it up(supposedly)
Definitions:
Create Timers:
Handlers:
Main() function...
I am working with the nRF5340 DK.
I am looking to sample an ADC pin to sample at a sampling frequency of at least 1kHz and I would like to use DMA to write the data directly...
Hi everyone, I implement nrf5_SDK_17.0.2 ble_app_uart example, but when I connect both GND wire and TX wire of the external device to my nRF52840 DK first, my nRF52840 DK...
Hi
As mentioned in this question: https://devzone.nordicsemi.com/f/nordic-q-a/69533/set-tx-power-on-zephyr-device , there is a sample to change the tx power using some HCI...
Hello,
I am trying to use the ble_app_rscs example app into the nRF5_SDK_17.1.0 package for connecting the nRF52840-DK board to the nRFToolbox Android application. However...
I have a small program that is to be used in production to test my device. It has to be scriptable so I'm using teraterm over rtt.
No external IO for a serial port.
Everything...
Hi Nordic,
Can you tell me how to remove commissioned a node from open-Thread ? Basically I want to remove a node from one network and put it in some other network. Are...
Hello,
I encountered a problem while trying to flash my PCA10040 nrf52 development kit.
I am able to compile my code in Segger Embedded Studio without a problem. The chip...
Hello:
I am using an nrf52840 on a custom board with W25Q01NV NOR Flash with the Nordic QSPI-NOR driver. Programming is with NCS v 1.8.0 (upgraded yesterday) and the VS...
Hi Team,
I am developing an application that required SPI communication with msp430.
But, some received characters are disorders, I see them by JLinkRTTViewer logs. For...
Hi
I'm using nRF51822 xxAA (256 Kbyte ROM). My code size are 66 690 byte, I'm using IAR.
Application memory setup:
This means that I have 131 KByte code size for my...
Hi,
I'm trying to configure my LTE modem (Icarus Board + nRF 9160 + SDK 1.7) with an external SIM.
For that i have to use the PDP configuration.
I use in my prj.conf...
Hi,
I am using SES and NCS SDK 1.6.1 under Win10.
A GPS module is connected to NRF5340, using an UARTE to communicate. The pin receiving GPS data is P0.31.
It works...
Hello,
I want to make sensor sleep and wake-up according to VDD.
- When VDD is below 2.8V, Sensor sleep.
- When VDD is above 2.8V, Sensor wake-up.
Since my board...
Hello,
We have a question from one of our customers as to whether the 52833 is compatible with the S340 Soft Device. On the Nordic website, it is not listed as a compatible...
