I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
Hi,
On nRF5340 development board I followed the instructions in this link and ran the blinky example successfully: Getting Started Guide — Zephyr Project Documentation...
I got an error here err_code = pm_init(); APP_ERROR_CHECK(err_code);
<error> nrf_ble_lesc: nrf_crypto_ecc_key_pair_generate() returned error 0x8502.
<error> peer_manager...
I am using the BLE sniffer in Wireshark (nrf 52840 dev kit board) to attempt to capture packets between a BLE device and android phone. I am able to sniff advertising packets...
Hi,
I have faced an issue with cmsis_v1 thread creation/removal with the SDK connect.
I have created the following ticket on zephyr's side and attached the patch I'm...
Hello,
How to find NRF connect mobile app server's address in the app to be used for connecting to peer devices ? Is there any way that the device address does not change...
Hi,
We are currently implementing the nRF52840 in an upcoming product and we have a question regarding component selection for our configuration.
I've looked through...
Hello
I really need your help !
I am using SEGGER Embedded studio with two EV boards: nRF9160 and NRF52 DK
First I started with NRF9160 with clean installation of the...
Hi
H have developed a program for nRF51822 using "Arduino IED" and "BLEPeripheral" library, that performs an operation.
The operation is a button press and on each press...
Hello,
My board reads data from acceleration sensor and sends it to ESB message.
When acceleration is under threshold, nRF52832 went sleep mode.
Before entering sleep...
Hi...
I am using Nordic SDK V17.0.2 with a SoftDevice S112 and developing a project uses freeRTOS that came with this SDK
From reading the documentation about the...
my project ,sample data every 4ms comes in a GPIOE interrupt ,and in interrupt give a data come semophere , but in thread take this data come semophere and read data can not...
Hello,
I am using NCS v1.6.0 with the nRF52833 DK and would like to modify the TX power (e.g. from 0 to +4 dBm) and PHY (e.g. from 1Mbps to Coded PHY) in the peripheral_uart...
