Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello. Developed with nrf52832 (S132 v7.0.1, SDK v16.0.0).
"pm_peer_delete" is used to delete the peer created during bonding. When I checked Flash when "PM_EVT_PEER_DELETE_SUCCEEDED...
Hi,
I have recently inherited a project from a former worker. The code intends to read data from a peripherial through TWI (the peripherial is a Si7053 digital temperature...
i used aplication twi_sensor form nRF5_SDK_12.3.0_d7731ad and i use s132.i conected mpu9060 every time get error on my terminl NRF_ERROR_BUSY.There is exemle of code main...
Hi,
I am working on a secure bootloader for a nRF52810 chip, and I am starting from the PCA10400e example in the SDK 16 and SD112 on SES (MacOS).
I successfully compiled...
Hi,
I am unable to get any programs using Zephyr to run on an nRF52840DK.
I have tried using the latest DAPlink (from GitHub) and JLink firmware (from Segger) as well...
When HFCLK was changed to "64 MHz crystal oscillator (HFXO)", the following code was implemented.
I am aware that "while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);" is waiting...
Hello all,
I would like to have some help regarding the usage of CoAP protocol. Is there any sample project that supports SDK 17.02 that I can start from?
I am using...
Hi DevZone,
Here's my setup:
Using NRF5 SDK 15.2.0, custom board based on NRF52840
Battery powered device with 3.6V battery.
Supply voltage stepped down to 1.8V...
Good day
Due to I am very new with NRF chips and I did not find direct answer on forum I require some clarification on that moment...
The task is to detect input pulse...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
Hello, with the new version of the nrf5340 version D in the NET CPU RTC0 stops to work and the RTC0 IRQ is not called
now for example the counter is stopped at 87 and the...
Hi,
My problem is that I can't sniff any advertising packet using Wireshark.
I have well followed the detailed procedure https://infocenter.nordicsemi.com/index.jsp...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
